Draw-Tite 60953 Instrucciones De Instalación

For vehicles with appearance
panel:
Remove appearance panel which
covers the trunk pan.
(2)10mm
Remove the (2) plastic rivets that
fasten the fascia tabs to the
vehicle. Note: Remove the center
of the rivet with a screwdriver.
Rivets to be reinstalled.
Return appearance panel and
fasteners to vehicle owner.
Equipment Required:
Fastener Kit: KA-8002-249
Wrenches: 11/16", 3/4"
Drill Bits: 9/16"
1
Qty. (2) BOLT CARRIAGE 7/16" - 14 X 1 1/2" GR 5
2
Qty. (2) WASHER CONICAL TOOTH 7/16"
3
Qty. (2) NUT – 7/16"
4
Qty. (1) BOLT CARRIAGE 1/2"-13 X 1 1/2" GR 5
1. Lower exhaust by removing both rubber isolators from muffler hangers. Be careful not to allow mufflers to fall under their own weight.
2. Both heat shields will need to be marked and drilled 4 1/2" from the forward most hole on the frame channel. Mark holes then hold
hitch in position to check. Refer to illustration for clarification. Remove heat shield to drill.
3. Thread bolt leader (9) onto end of carriage bolt (1) and insert bolt leader through reinforcing plate (7). Fish the bolt leader and
assembly through the access hole in frame and carefully pull through existing hole in frame till bolt is in position. Leave bolt leaders
attached so the hardware does not get pushed back inside the frame. Repeat for other side of vehicle.
4. Reinstall heat shields once the carriage bolts (1) are in position.
5. Install 1-1/2" carriage bolt (4) through square hole in hitch and vehicle's tie down loop from driver's side. Install clamping block (8) and
conical toothed washer (5) and nut (6) and hand tighten to hold hitch in place.
6. Fish bolt leaders through holes in hitch's frame straps and being careful not to push bolt assemblies back into frame channels, raise
hitch's frame straps up to vehicle's frame, remove bolt leaders and install conical toothed washers (2) and nuts (3).
7. Tighten all bolts, referring to torque table on instruction sheet.
8. Raise exhaust back into position and reinstall rubber isolators.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
Installation Instructions
HONDA ACCORD
Drawbar Kit:
3592
Drawbar must be used in the
RISE position only.
TIE DOWN LOOP
Tighten all 7/16 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft. (102N*M)
Includes Hybrid
6 cylinder
Do Not Exceed Lower of Towing Vehicle
2000 LB (908Kg) Max Gross Trailer Weight
200 LB (91Kg) Max Tongue Weight
Wiring Access Location: PC3
8
5
Qty. (1) WASHER CONICAL TOOTH 1/2"
6
Qty. (1) NUT – 1/2"
7
Qty. (2) PLATE REINFORCEMENT
8
Qty. (1) BLOCK; CLAMPING, 1-1/2" X 3"
Part Numbers:
Manufacturer's Rating or
FRAME RAIL
9
4 1/2" (114.3 mm)
Qty. (2)
9
BOLT LEADER
24787
60953
77161