Fountainhead ML Style Instrucciones Del Ensamblaje

The Fountainhead Group, Inc.
Owner's Manual
"ML" Style
Do not return sprayer to store, if you experience problems or have questions contact our toll free
Customer Service Center, M-F 8 a.m. - 5 p.m., EST, at 1-800-311-9903, or e-mail:
Info@TheFGI.com, or access online at: www.TheFountainheadGroup.com.
WARNING
The sprayer is operated with liquid under pressure. Failure to observe CAUTION and to follow instructions
for operating and cleaning can cause tank, hose and other parts to be weakened and rupture under pressure.
This can result in serious injury from high pressure discharge of liquids or forcible ejection of parts. DO NOT
USE FLAMMABLE MATERIALS IN THIS SPRAYER. Material could ignite or explode, causing serious injury
and/or possible death. For safe use of this product, you must read and follow all instructions before use.
TEST SPRAYER WITH WATER BEFORE USING ANY CHEMICALS.
SAFETY PRECAUTIONS
• Read owner's manual completely before operating this • Do not pressurize with any mechanical device such as an
sprayer. air compressor, since this can create a dangerous pressure
• Always wear safety goggles, gloves, and protective clothing level and bursting of parts resulting in serious injury. Only
when using sprayer.
use original or replacement pump supplied by the original
• Read and follow all instructions and cautions on label of
manufacturer.
products used in this sprayer.
• Do not store chemicals in this tank.
• Never use fl ammable liquids, caustics, acids, or hot water in
• Always release pressure when sprayer is not in use and before
this tank.
removing pump from tank.
• Do not leave sprayer in the sun when not in use.
• Do not stand with face or body over top of tank when pumping
• Spray when air is calm to prevent drift of chemicals.
or loosening pump, to prevent pump and/or solution from
• Do not use sprayer near open fl ame or anything that could
striking you, resulting in serious injury.
cause ignition of the spray.
• Clean and rinse sprayer thoroughly after each use.
• Always inspect the hose and all hose connections before each
• Never attempt to alter sprayer from original condition.
use. A damaged hose, or loose hose connection can result in
• Always use replacement parts from original manufacturer.
unintended exposure to the pressurized chemical, resulting in
• Keep the sprayer and all chemicals out of the reach of children
serious injury or property damage.
and pets.
• Do not lift or carry sprayer by the hose, shut-off valve, or
wand extension. Carry by pump handle only, making sure
handle is properly locked in place before lifting.
TROUBLESHOOTING
TROUBLE LOOK FOR
Sprayer starts to spray when pumping Shut-off lock is engaged.
or sprayer will not stop spraying when
shut-off handle is released.
Sprayer leaks at pump or sprayer does 1. Dirt or debris on pump gasket or
not build pressure. closure.
2. Chipped, torn, swollen or defective
pump gasket.
3. Check valve at bottom of pump
assembly.
4. Inspect o-ring on piston.
Sprayer material overfl ows through 1. Dirt or debris under check valve on
pump barrel or pump handle rises pump.
when handle is unlocked. 2. Chipped, torn or swollen pump
check valve.
Hose leaks at tank. 1. Loose hose.
2. Cracked, swollen or faulty hose.
Hose leaks at shut-off. Swollen, slit or faulty hose
Sprayer is diffi cult to pump. 1. Damaged piston o-ring.
2. Piston o-ring is dry.
Nozzle drips when shut-off handle is Dirt or debris in shut-off valve.
released.
Sprayer tank leaks. Evidence of spray material escaping
from the tank.
Nozzle tip leaks, poor spray pattern, 1. O-ring is missing or damaged.
partial spray or complete stoppage. 2. Spray extension or nozzle clogged.
Limited Warranty
Warranty card is provided in unit parts bag or call our toll free hotline, or access online at www.TheFountainheadGroup.com
To obtain warranty service, contact us at: The Fountainhead Group, Inc., c/o Customer Service, 23 Garden Street, New York Mills,
New York 13417, (315) 736-0037 or call prepaid, (800) 311-9903
ASSEMBLY INSTRUCTIONS
It is recommended to test the sprayer using plain tap water before spraying chemicals. Test all connections for
possible leaks. Use proper eye protection while testing. If sprayer does not pass the water test, call our
Customer Service Center before using sprayer with chemicals. Make sure hose is not cracked or frayed and
does not show signs of swelling. Make sure hose is securely connected to sprayer.
DO NOT USE TOOLS TO TIGHTEN HOSE NUT.
Assemble Hose to Tank
1a. Align hose barb tabs, push hose barb into
tank until it stops.
2a. Slide hose nut into place and turn clockwise
to tighten.
"O" Style
1a
Install the Nozzle
Select using Nozzle Chart
B
A C D
H
NOZZLES INCLUDED WILL VARY DEPENDING ON
SPRAYER MODEL PURCHASED
A. Adjustable Cone E. Yellow Low-Volume
Nozzle
B. Cap Nut F. Foaming Nozzle
C. Blue Watering Nozzle G. O-Ring (some models
D. Red High-Volume
Fan Nozzle H. Extension
OPERATING THE SPRAYER
REMEDY
This sprayer is designed for lawn and garden use only. Do not use harsh chemicals or cleaners.
Squeeze shut-off handle and
disengage the lock.
Filling
Fill the tank to the desired level.
1. Clean dirt or debris from gasket or (Always refer to chemical manufacturer for
closure.
proper mixture).
2. Remove old gasket and replace with
1a. REMOVE PUMP: Turn handle counter-
new.
clockwise
3. Replace if missing or damaged.
2a. INSTALL PUMP: Turn handle clockwise
4. Lubricate the pump as described in
Regular Maintenance section. until tightly sealed on tank.
1. Clean check valve and valve sealing
surface on pump.
2. Replace check valve.
1. Tighten hose nut.
2. Replace shut-off assembly.
Replace shut-off assembly.
1a
1. Replace piston o-ring.
Spraying and Locking
2. Lubricate the pump as described in
Regular Maintenance section.
1. Squeeze shut-off handle to begin spraying.
1. Replace shut-off assembly.
2. Release shut-off handle to stop spraying.
2. See Shut-off Maintenance section.
3. For continuous spraying, squeeze handle
and slide lock as shown.
Replace entire sprayer.
1. Replace o-ring at extension tip.
2. If applicable to sprayer model, remove
and clean the extension and nozzle.
Manual No. 181555 - Universal Sprayer
"O" Style
Rev. C Date: 09/06/2013
ECN13-077
11" x 17" Folded to 3 3/4" x 5 3/4"
Do not attempt to heat or alter hose, hose nut, or barb prior to assembly.
Assemble Extension to Shut-Off
1b. Install the extension onto the shut-off assembly
and tighten the nut securely.
1b
Note: Some extensions are sold preassembled to
nozzle and shut-off as a complete assembly.
2a
Turn to adjust ADJUSTABLE CONE USES: BLUE WATERING NOZZLE USES:
spray pattern.
Spot spraying in or around flower Watering and feeding plants and
beds, trees, and shrubs.
vegetables both indoors and
Edging along fences, driveways, and
outdoors.
walkways.
Killing brush such as poison ivy,
poison oak, kudzu and wild
blackberry.
Preparing garden beds for planting
of ornamentals and vegetables.
RED HIGH VOLUME YELLOW LOW VOLUME
FAN NOZZLE USES: FAN NOZZLE USES:
E F
Lawn replacement. Kill lawn and For precision spraying in confined
weeds before planting a new lawn. areas such as gardens and flower
Preparing large areas for planting of beds.
ornamental and vegetable gardens.
G
FOAMING NOZZLE USES:
Spot spraying in flower beds,
Fan Nozzle walkways, driveways, and patios,
around trees and shrubs.
Edging along fences, driveways
and walkways.
Killing brush such as poison ivy,
are sold pre-assembled to extension)
poison oak, kudzu and wild
blackberry.
Read Safety Precautions! Always make sure the pressure is released
from the tank before fi lling or servicing.
Pressurizing
Make sure shut-off handle lock is not engaged. (If lock
is engaged while pressurizing, the unit will immediately
start spraying).
1b. Push down on the handle and turn counter-clockwise
to unlock the handle.
2b. Pump handle in a smooth up and down motion until
pressure builds up.
3b. Push down on handle, turn clockwise to lock in place.
2a 1b 2b
Release Tank Pressure
Pressure Release Valve (PRV) on select models
1c. NO PRV: Place tank on side or upside down, direct
nozzle away from face and body, squeeze shut-off
handle and hold down until unit stops spraying.
2c. WITH PRV: Pull up PRV until all pressure is
released.
1c
"ML" Style
Finish
1. Depressurize the tank as described in Release Tank Pressure section.
A.) Lay tank on its side with the hose outlet on the bottom. Direct nozzle away from face and body and
squeeze the shut-off handle until unit stops spraying. This will release pressure in the tank.
B.) On select models with Pressure Release Valve (PRV), pull up on the PRV until all the pressure is released
from the tank.
2. Turn the pump handle counter-clockwise to remove the pump.
3. Empty any remaining liquid according to the product disposal directions.
4. Follow Cleaning instructions.
Cleaning
1. Fill the tank with clean tap water. Replace the pump and tighten securely.
2. Agitate the tank to rinse the chemicals from the tank wall and pump.
3. Remove the pump and empty the contents into gravel or bare soil.
4. Refi ll the tank with clean tap water.
5. Make sure the pump is free of dirt or debris, and re-install into the tank. Tighten securely.
6. Pressurize the tank as described in the Pressurizing section.
7. Direct the nozzle away from yourself and squeeze the shut-off handle for at least 30 seconds to clean the hose
and shut-off.
8. Release pressure as described in the Release Tank Pressure section.
9. Remove the pump and empty the contents into gravel or bare soil.
10. Repeat steps 1-9 until thoroughly cleaned.
Sprayer Storage
1. Sprayer tank should be hung upside down, with the pump removed.
2. Do not store or leave any solution in tank after use.
3. Store in warm, dry location out of direct sunlight.
4. Keep the sprayer and all chemicals out of reach of children.
REGULAR MAINTENANCE -
Lubrication
Pump should be periodically oiled by
applying 10 to 12 drops of light oil
down the pump rod through the
opening in the pump cap, as shown:
"ML" Style "O" Style
O-rings dry out and become brittle.
Apply petroleum jelly liberally to part(s)
as shown, or replace.
Shut-Off Maintenance
If shut-off clogs, remove and disassemble the shut-off assembly.
Clean the openings of any obstructions and re-assemble tightly securing all sections.
3b
"ML" Style
This shut-off is not serviceable.
SERVICE KITS AND REPAIR PARTS ARE AVAILABLE.
Contact Customer Service at 1-800-311-9903,
e-mail: Info@TheFGI.com, or
2c website: www.TheFountainheadGroup.com
Pump & Shut-Off Maintenance
Disassembly & Reassembly
As shown on varying models
1. Remove pump from tank.
2. Push tabs in on both sides of the
pump cylinder and pry up pump cap.
3. Pull pump handle out of barrel,
lubricate o-ring as required.
4. Replace pump cap, align tabs on
pump cap and barrel, and push down
until tabs lock in place. "ML" Style
1. Remove pump from tank.
2. Squeeze tabs that lock barrel and
turn counter-clockwise to unlock.
3. Remove barrel, lubricate o-ring as
"O" Style
required.
4. Re-insert barrel into cap, turn barrel
clockwise to lock tabs back in place.
o-ring
"O" Style
Clean out or replace parts.