Domyos ENERGY RUN Manual De Instrucciones página 18

Adjusting the tension of the walking belt:
The walking belt is susceptible to wear and tear and can stretch over time. Re-tighten it as soon as it begins to slip
(skidding feeling with sudden changes in speed).
• Turn both adjusting screws by half a turn clockwise.
• Repeat procedure if necessary but make sure that the belt is not too tight. The belt is correctly tightened if you can lift the edges
by 2 to 3 centimetres on each side.
MAINTENANCE EVERY 200 HOURS OF USE OR EVERY 1500 KM
To find out the duration of use and the distance travelled since the treadmill was started up, refer to the INFORMATION MODE section.
Lubricating the treadmill belt:
It is important to lubricate your treadmill in order to reduce friction between the walking belt and the deck. If you note traces
of silicone on the inner surface of the walking belt (damp, wet and slightly greasy surface), there is no need to lubricate.
.
„ DIAGNOSING ERRORS
The treadmill doesn't switch on:
1. Check that the power cable is plugged into a functioning wall socket (to check if the wall socket is working, plug in a lamp or other electrical
device).
2. Check that the power cable is plugged into a correctly earthed wall socket. If you need an extension cable, use one fitted with an earth
connection which is no longer than 1.5 m in length.
3. Once you've plugged in the power cable, check that the key is properly inserted into the console.
4. Check the circuit breaker, located on the treadmill frame, near the power cable. If it is protruding, as shown, the circuit breaker has tripped.
To reset, wait for 5 minutes and then push the switch back in.
The treadmill switches off when in use:.
• Check the circuit breaker, located near the power cable. If it is in the OFF position,
wait 5 minutes, then switch to the RESET position.
• Check that the power cable is plugged in.
• Remove key from console. Reinsert key into console.
If the problem persists, contact the after-sales service team (see last page of instructions).
The console screen remains on when you remove key from console:
The console has a demo mode which is designed to be used when the treadmill
is displayed in store. If the screen remains lit when you remove the key from the console,
the demo mode is probably turned on. To disable the demo mode, refer to paragraph
entitled INFORMATION MODE.
The belt slows down when you walk on it:
• If you need to use an extension cable, you must only use a cord with 3 x 1 mm² conductors (size 14), which is no longer than 1.5 m (5 ft)
in length.
• If the walking belt is over-tightened, your treadmill performance may be adversely affected and the walking belt may become damaged
To adjust the tension of the belt, refer to the paragraph entitled MAINTENANCE.
If the problem persists, contact the after-sales service team (see last page of instructions).
The incline system does not function property:
Recalibrate incline system:
1. Change the incline by pressing one of the incline adjusting buttons.
2. During the recalibration process, remove the safety key from console then unplug treadmill.
3. Wait a few seconds then plug in treadmill once again and insert safety key into console.
The treadmill will automatically rise to the maximum incline level then return to the minimum level.
If the belt and deck are dry:
• Switch off treadmill and unplug.
• Lift the edges of the walking belt and coat the inner surface with silicone.*
• Plug in treadmill.
• Before using, run the walking belt at 4km/h (2.5 mph) for 10-20 seconds.
• Your treadmill is now ready to use!
* One lube application usually requires between 5 and 10 ml of silicone. Warning: a surfeit
of silicone can adversely affect the functioning of your treadmill (risk of slipping).
To purchase belt lube, please contact your local DECATHLON store.