Publicidad
Idiomas disponibles
Idiomas disponibles
1. Lower the window and ensure the locking rod is in the unlocked
position. Use a flat-bladed tool to disengage the detent tab from
the lock rod knob assembly (1) and remove the knob by pulling
upward. When reinstalling, push the knob down until the detent
tab touches the locking rod opening cover and engage the detent
tab.
2. Insert a flat-bladed tool between the door handle bezel cover (2)
and the trim panel to release and remove. Repeat this process for
the trim panel cover (3) to release the retainers (3) and remove.
When re-installing the bezels to the door panel, press the bezels
into place until they are completely seated.
3. Remove the 3 – 10 mm trim panel bolts (4). When replacing,
tighten to 2 N·m (18 lb in). TIP: Use a pencil magnet to assist in
removing and installing the bolts.
4. Remove the door trim panel assembly (5) by pulling the trim away
from the door panel to disengage the 12 retainers (6). IMPOR-
TANT NOTE: There are 2 hooks located on the lower portion of
the door trim panel that are used for manufacturing installation
ONLY. If these hooks are damaged during either removal or
installation of the door trim panel, replacement of the panel is not
required. When re-installing the trim panel, start at the lock knob,
pushing down and outward while moving toward the upper front.
5. Disengage the door cable from the retaining clip (7) by pulling it
out and away.
Door Insulator
1. The door insulators are attached to the door trim at all
corners. Take due care to not tear the insulator. After the
trim panel has been disengaged, unbutton the retainers from
the insulator prior to removing the door trim panel. These
retainers are used for manufacturing installation only and are
not needed for reinstallation.
Trailer Mirrors
ALL INFORMATION WITHIN
DATE
ABOVE BORDER TO BE PRINTED
EXACTLY AS SHOWN ON 8.5 x 11
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCOR-
DANCE WITH GMSPO SPECIFI-
CATIONS.
REVISION
AUTH
2. Use a flat-bladed tool to separate the bond between the
sealer and the door. Take due care to not damage the
adhesive during removal. If needed, use 3M 777 waterproof
tape.
3. When reinstalling the water deflector, clean the door adhe-
sive area using a 50/50 mix of isopropyl alcohol or equiva-
lent.
Power Mirror Replacement
1. Remove the 3 – 10 mm nuts (2) retaining the outside mirror.
When re-installing, tighten to 9 N·m (80 lb in).
2. Disengage the three wiring retainer clips (1) by gripping the center
of each clip with pliers and pulling. When re-installing, fully seat
each clip.
3. Remove the mirror assembly (3) from the door.
4. Install the Driver's Switch Assembly (if provided) and the Trailer
Towing Mirror Assemblies included in this package in the reverse
order that the original parts were removed.
5. To complete the installation, follow the instructions in the reverse
order to reinstall the trim components.
6. The driver's switch must be reprogrammed with the latest calibra-
tion software by an authorized GM vehicle dealership in order for
the Trailer Towing Mirrors to operate correctly. The dealership will
use the Service Programming System (SPS) to program the
Driver Door Module (DDM) and Passenger Door Module (PDM) by
selecting the trailer towing mirror option DPN. This will complete
the programming portion of the installation.
PART NO.
REV 16AU07
INSTALLATION INSTRUCTIONS
DR
TITLE
PART NO.
19201573
6200 Grand Pointe Dr., Grand Blanc, MI 48439
19201573
SHEET
Trailer Mirrors
3
SHEET
3
18
OF
18
OF
Publicidad
