Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Body Side Molding
Kit Contents
Description
Molding Front (Left Hand)
Molding Front (Right Hand)
Molding Rear (Left Hand)
Molding Rear (Right Hand)
Alcohol Swab
Installation Instructions
Tools Required
Measuring Tape
Masking Tape
Roller
Vehicle Preparation
1. Temperature must be between 61°F-86°F (16°C-31°C).
2. Wash and thoroughly dry vehicle.
3. Wipe vehicle thoroughly with alcohol swab where receiving parts. Care and time should be
taken on this step to give good tape adhesion.
4. For best results, vehicle should be free of damage (dents, scuffs, creases, fractures, etc.)
Body Side Molding Installation
1. Measure from the bottom of the doors and use masking tape as a guide. See Figure 1A.
FIGURE 1A
ALL INFORMATION WITHIN ABOVE
DATE
BORDER TO BE PRINTED EX-
ACTLY AS SHOWN ON 8.5 x 11
14SE04
WHITE 16 POUND NON-BOND
RECYCLABLE PAPER.
PRINT ON BOTH SIDES, EXCLUD-
ING TEMPLATES.
TO BE UNITIZED IN ACCORDANCE
WITH GMSPO SPECIFICATIONS.
Quantity
1
1
1
1
4
1
29mm
MASKING
TAPE
320mm
332mm
Body Side Molding
REVISION
MASKING
TAPE
332mm
PART NO.
INSTALLATION INSTRUCTIONS
AUTH
DR
TITLE
PART NO.
88966645
6200 Grand Pointe Dr., Grand Blanc, MI 48439
3mm
3mm
MASKING TAPE
342mm
88966645
SHEET
Body Side Molding
1
SHEET
1
6
OF
6
OF
Publicidad
Manuales relacionados para GM 88966645
Resumen de contenidos para GM 88966645
- Página 1 FIGURE 1A 29mm MASKING MASKING TAPE TAPE MASKING TAPE 320mm 332mm 342mm 332mm 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION AUTH TITLE BORDER TO BE PRINTED EX- ACTLY AS SHOWN ON 8.5 x 11...
- Página 2 NOTE: CARE SHOULD BE TAKEN NOT TO DAMAGE THE PAINT FINISH. FIGURE 1B 2" (50mm) MASKING TAPE SIDE MOLDING FRONT SIDE MOLDING REAR (RIGHT HAND) (RIGHT HAND) 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION...
- Página 3 29 mm 3 mm RUBAN- RUBAN- CACHE CACHE RUBAN-CACHE 320 mm 332 mm 332 mm 342 mm 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION AUTH TITLE BORDER TO BE PRINTED EX- ACTLY AS SHOWN ON 8.5 x 11...
-
Página 4: Installation Instructions
REMARQUE : DES PRÉCAUTIONS DOIVENT ÊTRE PRISES POUR ÉVITER D’ENDOMMAGER LE FINI DE PEINTURE. FIGURE 1B 50 mm (2 po) RUBAN-CACHE BAGUETTE DE PROTECTION BAGUETTE DE PROTECTION LATÉRALE AVANT (CÔTÉ DROIT) LATÉRALE ARRIÈRE (CÔTÉ DROIT) 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION... - Página 5 3 mm CINTA DE CINTA DE ENMASCARAR ENMASCARAR CINTA DE ENMASCARAR 320 mm 332 mm 342 mm 332 mm 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION AUTH TITLE BORDER TO BE PRINTED EX- ACTLY AS SHOWN ON 8.5 x 11...
- Página 6 NOTA: TENGA CUIDADO DE NO DAÑAR EL ACABADO DE LA PINTURA. FIGURA 1B 50 mm (2") CINTA DE ENMASCARAR MOLDURA LATERAL DELANTERA MOLDURA LATERAL TRASERA (LADO DERECHO) (LADO DERECHO) 88966645 Body Side Molding PART NO. SHEET INSTALLATION INSTRUCTIONS ALL INFORMATION WITHIN ABOVE DATE REVISION AUTH...