Black and Decker Workmate 375 Manual De Instrucciones

Workmate 375
®
Copyright © 2002 Black & Decker Printed in Canada
Cat. No. WM375 Form No. B&D 244323-00, Camalor C10341-00 Rev. A (AUG. '02)
IMPORTANT SAFETY INSTRUCTIONS
1. Do not load with more than 350 pounds.
2. Do not apply an unbalanced load which could cause the Workmate to tip
over.
3. Do not use the Workmate as a stepladder or standing platform.
4. Do not store Workmate outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the swivel pegs.
6. Be sure that the legs are fully open and that the release bar and work
surface locks in position.
7. When using a power tool with the Workmate, follow the safety instructions
in the tool's instruction manual.
8. Always wear safety glasses when operating power tools.
9. An even pressure of the vise jaws on the workpiece is essential. Tighten
both crank handles uniformly.
10. Cutting or drilling into work surface may result in striking metal jaw
support below, damaging tool or work centre.
11. Caution required when using high temperature tools (heat guns, torch, solder
iron, etc.). May damage work surface and reduce clamping capability.
12. Do not step on or stand on cross member tool holder.
SAVE THESE INSTRUCTIONS FOR FUTURE USE.
Fig.1
Fig. 2
Fig. 3
Fig. 4.
Fig. 5 Fig. 6.
Fig. 7.
Fig. 8
Fig. 9
To Close Unit: (Fig. 8)
a) Place foot on foot pad. (Step 1)
b) Grip the front vise jaw and tilt unit towards you. (Step 2)
c) Place hand beneath the front vise jaw and squeeze wire release handle
towards you (Step 3) and lift up Step 4). Continue until unit is folded.
FEATURES & APPLICATIONS:
Swivel Pegs:
The four supplied swivel pegs can be used in any of the holes in the front and
rear jaws. The pegs are used to extend the size of your Workmate's holding
capacity.
Service Information
Black & Decker offers a full network of company-owned and Authorized Service
locations throughout North America. All Black & Decker Service Centers are
staffed with trained personnel to provide customers with efficient and reliable
power tool service. Whether you need technical advice, repair, or genuine
factory replacement parts, contact the Black & Decker service location nearest
you. To find your local service location, refer to the yellow page directory under
"Tools—Electric" or call: 1-800-54-HOW-TO.
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any
defects in material or workmanship. The defective product will be replaced or
repaired at no charge in either of two ways:
The first, which will result in exchanges only, is to return the product to the
retailer from whom it was purchased (provided that the store is a participating
retailer). Returns should be made within the time period of the retailer's policy
for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be
required. Please check with the retailer for their specific return policy
regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker
owned or authorized Service Center for repair or replacement at our option.
Proof of purchase may be required. Black & Decker owned and authorized
service centers are listed under "Tools-Electric" in the yellow pages of the phone
directory.
This warranty does not apply to accessories. This warranty gives you
specific legal rights and you may have other rights which vary from state to
state. Should you have any questions, contact the manager of your nearest
Black & Decker Service Center.
This product is not intended for commercial use.
See 'Tools-Electric'
701 E. Joppa Rd.
– Yellow Pages –
Towson, MD 21286
for Service & Sales
Black & Decker
(U.S.) Inc.,
U.S.A.