Publicidad
Idiomas disponibles
Idiomas disponibles
EN
iOCT41 – 4 Digital Inputs + 1 Open-
Collector Output
Features:
•
4 digital inputs;
•
1 open collector output up to 500mA @ 15V;
•
reads 3 types of clicks;
•
reads security equipment (PIR, Gas, Fire detectors);
•
reads status switches (open/ closed);
•
MdiBus interface;
•
Installation in junction boxes;
Applications:
•
Reading of push-buttons, switches and motion
detectors.
•
Relay control.
Specifications:
Power supply voltage: 15VDC;
Consumption: 18mA nominal @ 15VDC or 518mA @15VDC,
when supplying current to the output.
Storage temperature: -10ºC a 60ºC;
Operating temperature: 10ºC a 50ºC;
Maximum humidity: 80% non-condensing;
Output specifications:
Nominal current: 500mA;
Maximum voltage: 15VDC;
Inputs specifications:
Nominal voltage: 5VDC low voltage;
Maximum allowable contact resistance: 50Ω;
Physical Specifications:
Dimensions: 46mm X 42mm X 28mm;
Protection degree: IP00, for indoor use;
Compatibility:
Compatibility with iThink module: V1.0 or higher.
Compatibility with Mordomus software: Mordomus iThink
V2017 or higher.
ATTENTION:
Never crimp or cut cables while they are connected
to powered equipment.
The module is not provided with additional protection
against short circuit, therefore it is recommended to
use a power supply with the correct specifications.
Mordomus shall not be liable for any damages
resulting from the use of our equipment outside the
specifications and/or for a purpose other than that
intended.
Due to the nature and reduced size of the module it is
not contained in any type of encapsulation and
should be treated accordingly. Prevent contact
iOCT41
between the module and any metallic or conductive
surface.
Overview:
MdiBus IN and power supply connector
MdiBus OUT and power supply connector
Status LEDs
Addressing button
Output status LED
Input and output connector
iPSB connector
Connections:
Specification of MdiBus conductors: CAT 6 UTP
Connection table MdiBus and power supply - refer to
nr.
,
and
:
Terminal of iPSB
Cable color
Terminal of
(Eg. Branch 1)
(UTP CAT6)
16
Green
MDiBus A OUT (Eg. Branch 1)
15
Green/White
MDiBus B OUT (Eg. Branch 1)
14
Blue
MDiBus A IN (Eg. Branch 1)
13
Blue/White
MDiBus B IN (Eg. Branch 1)
18
Orange
+ 15VDC
17
Orange/White
GND
18
Brown
+ 15VDC
17
Brown/White
GND
17
Shielding
GND
Connection table Inputs and output - refer to
image
Terminal of
Function
+15V Output
GND
Digital Input Ch1
Digital Input Ch2
Digital Input Ch3
Digital Input Ch4
Open-collector output Ch1
HW 1.0
MDiBus and 15VDC power supply connection: The iOCT41
should be connected to the MdiBus and the power supply via the
iPSB module using UTP Cat6 cable.
connections in the previous Table should be respected. The
example specifies the wiring from iOCT41 to the branch 1 of the
iPSB module.
Image
1.
Connecting more than one iOCT41 on the same iPSB branch:
The connection of multiple iOCT41 modules in the same extension
is possible as long as the MDiBus passes through all the iOCT41
modules and the last iOCT41 module has the MDiBus return
connected to the MDiBus A IN and MDiBus B IN. See
Enrollment:
To enroll the iOCT41 module proceed as follows:
1.
Make sure that the iOCT41 is powered by a suitable
power supply and connected to the MdiBus via an
iPSB module
,
2.
In the Mordomus software access the menu
Configurations and access the sub-menu Modules/
image
1,
Addresses.
3.
On the iOCT41, press and hold the addressing button
for at least 1sec. The green LED
iOCT41
slowly until the addressing is complete.
4.
The iOCT41 should be added automatically to the list
3
and the green LED
should stop blinking.
2
Types of digital input clicks: A single click is performed by
3
pressing the button connected to the corresponding digital
2
input briefly (approx. 1/10 second). A double click is performed by
pressing the button briefly (approx. 1/10 second) twice. A long click
4
is performed by pressing the button for longer than 1 second.
1
Inputs set for detector reading (movement, gas, etc.) are
limited to one event/detection every 20 seconds. After an
4
event, no other events will be detected for 20 seconds on this
input.
1
The input type of each channel as well as other parameters
1
can be defined in the Mordomus Software by selecting the
desired input in Configurations, Modules/Addresses.
1, nr.
Reset:
To perform a reset to the module, interrupt the 15VDC
iOCT41
power supply for 5 seconds.
9
10
11
LED codes
:
12
13
Green LED ON: Module powered and enrolled to software;
14
Red LED ON: Module powered and not enrolled to software;
15
Green and Red LEDs blinking simultaneously: Under-voltage
protection mode. Power supply voltage is to low;
v.2105
Green LED blinking continuously: Module awaiting address
definition;
The wire colors and
Red LED flashing: Module sending/receiving data.
Yellow LED
ON: Output is on.
Yellow LED
OFF: Output is off.
This product complies with the Electromagnetic
Compatibility Directive 2014/30/EU.
image
2.
This product conforms with the EU Directive 2011/65,
RoHS
regarding the restriction of use of certain hazardous
substances in electric and electronic devices.
For EU countries only.
All old electrical and electronic devices must be
separated from normal household waste and disposed
of at designated facilities. For further information
contact your local authorities, waste disposal office or
the shop where you bought the device.
and
.
http://mordomus.com/mordomus/docs/ithink/iOCT41.pdf
http://mordomus.com/mordomus/docs/ithink/iPSB.pdf
will blink
2/5
Publicidad
