Publicidad
Idiomas disponibles
Idiomas disponibles
English
INSTALLATION INSTRUCTIONS
Water Supply
Recommended
Maximum
Hot Water Temperature
65 C° (~150F)
80 C° (~175F)
Working Pressure
3 BAR (~45PSI)
5 BAR (~75PSI)
In case of pressures over 5 BAR (~75 PSI), we
screw (4.E), then tighten the latter.
Warning! Do not force the screw (4.E).
recommend to use a pressure reducer. Before
proceeding with the assembly, purge the
Excessive tightening can affect the correct
hot and cold water pipes so as to avoid the
function of the system or damage it. The
accumulation of dirt and impurities that could
thermostatic cartridge is equipped with a safety
affect the function of the faucet.
anti-scalding retainer set at 100°F (38°C). For
higher temperatures push the button on the
FIG. 01
adjustment handle. In case of hot or cold water
Remove the protection covers (1.A) using a
pressure failure, the flow will automatically stop.
screwdriver. Use the plug (1.B) if necessary.
With a screwdriver loosen the stop cocks (4.F)
in anti-clockwise direction.
FIG. 02
Fit the faucet body (2.A) to the wall with the
FIG. 05
two upper outlets pointing towards the flow
Remove the protection tape of the adhesive
elements. Connect the hot water supply to the
sponge (5.D) and apply it on the back of the
left inlet and the cold water supply to the right
plate (5.C). Fit the sliding flat washers (5.B) and
one.
(5.A) on the plate (5.C) and install it on the
thermostatic body till it is flush to the wall.
FIG. 03
FIG. 06
The depth of the wall niche must correspond
(wall coating included) to the tolerance given by
Control handles installation. For the upper
the MIN/MAX references given on the plastic
portion with the diverting cartridge, follow the
cover (3.A). Once all connections have been
instructions given below:
carried out, activate the faucet at the working
Fit the spacers (6.P-6.O) on the bar of the
pressure (we recommend maintaining the water
cartridge, screw on the protection cylinder
flow for a few minutes so as to purge the system
(6.N), install the insert (6.M) and fasten with
from any debris and/or dirt inside the piping).
the included screw (6.I) placing the spacer in
Temporarily remove the protection cover (3.A)
between. Fit the handle (6.F) and tighten the
to check if there are leakages and if the system
grub screw (6.G). Complete by positioning the
works regularly, reinstall the protection cover
finishing cap (6.H). For the lower portion with
(3.A) and finish the external wall surface.
the thermostatic cartridge, follow the instructions
given below: fasten the peg (6.E) on the bar of
FIG. 04
the thermostatic cartridge and install the handle
Remove the protection cover (3.A) as shown
(6.A) putting the ring (6.D) in between without
in FIG. 03. With a screwdriver fasten the stop
moving the bar so as to not compromise the
cocks (4.F) in clockwise direction, loosen the
cartridge calibration. Tighten the grub screw
fitting screw (4.E) using the proper wrench
(6.B) and place the finishing cap (6.C).
and pull out the test plug (4.D). Insert the o-ring
(4.C) and the sleeve (4.B) on the thermostatic
FIG. 07
body. Use a small quantity of the special grease
To replace only the handle (7.A) follow the
included to lightly lubricate the o-rings of the
instructions given below:
thermostatic cartridge (4.A). Insert the cartridge
Remove the cap (7.Y), loosen the grub screw
in the faucet housing carefully aligning the
(7.B) and pull out the handle (7.A).
positioning hole with the housing of the fitting
Install the new handle (7.A) and fasten it using
FIG. 01
Minimum
15 C° (~60F)
0.5 BAR (~7PSI)
FIG. 03
FIG. 05
FIG. 02
FIG. 04
FIG. 06
FIG. 07
FIG. 08
Publicidad
