Publicidad
Idiomas disponibles
Idiomas disponibles
English
INSTALLATION INSTRUCTIONS
Water Supply
Recommended
Maximum
Hot Water Temperature
65 C° (~150F)
80 C° (~175F)
Working Pressure
3 BAR (~45PSI)
5 BAR (~75PSI)
In case of pressures over 5 BAR (~75 PSI), we
housing of the fitting screw (4.F), then tighten
recommend to use a pressure reducer.
the latter.
Warning!, Do not force the screw (4.F).
Before proceeding with the assembly, purge the
hot and cold water pipes so as to avoid the
Excessive tightening can affect the correct
accumulation of dirt and impurities that could
function of the system or damage it. The
affect the function of the faucet.
thermostatic cartridge is equipped with a safety
anti-scalding retainer set at 100°F (38°C). For
FIG. 01
higher temperatures push the button on the
Remove the protection covers (1.A) using a
adjustment handle. In case of hot or cold water
screwdriver. Use the plug (1.B) if necessary.
pressure failure, the flow will automatically stop.
With a screwdriver loosen the stop cocks (4.G)
FIG. 02
in anti-clockwise direction.
Fit the faucet body (2.A) to the wall with the
two upper outlets pointing towards the flow
FIG. 05
elements. Connect the hot water supply to the
Remove the protection tape of the adhesive
left inlet and the cold water supply to the right
sponge (5.D) and apply it on the back of the
one.
plate (5.C).
Fit the sliding flat washers (5.B) and (5.A) on
FIG. 03
the plate (5.C) and install it on the thermostatic
The depth of the wall niche must correspond
body till it is flush to the wall.
(wall coating included) to the tolerance given
FIG. 06
by the MIN/MAX references given on the
plastic cover (3.A).
Control handles installation.
Once all connections have been carried out,
For the upper portion with the cartridge, follow
activate the faucet at the working pressure
the instructions given below:
(we recommend maintaining the water flow
Fit the insert (6.M) on the bar of the cartridge
for a few minutes so as to purge the system
so as to obtain the correct alignment once the
from any debris and/or dirt inside the piping).
handle (6.G) has been installed and lock using
Temporarily remove the protection cover (3.A)
the screw included (6.L). Fit the handle (6.G)
to check if there are leakages and if the system
and tighten the grub screw (6.I). Complete by
works regularly, reinstall the protection cover
positioning the finishing cap (6.H).
(3.A) and finish the external wall surface.
For the lower portion with the thermostatic
cartridge, follow the instructions given below:
FIG. 04
fasten the peg (6.E) on the bar of the thermostatic
Remove the protection cover (3.A) as shown
cartridge and fit the spacer (6.F). Install the
in FIG. 03. With a screwdriver fasten the stop
handle (6.A) putting the ring (6.D) in between
cocks (4.G) in clockwise direction, loosen the
without moving the bar so as to not compromise
fitting screw (4.F) using the proper wrench and
the cartridge calibration. Tighten the grub screw
pull out the test plug (4.D). Insert the o-ring
(6.B) and place the finishing cap (6.C).
(4.C) and the sleeve (4.B) on the thermostatic
FIG. 07
body and protection cylinder (4.E). Use a small
quantity of the special grease included to lightly
To replace only the handle (7.A) follow the
lubricate the o-rings of the thermostatic cartridge
instructions given below:
(4.A). Insert the cartridge in the faucet housing
Remove the cap (7.C), loosen the grub screw
carefully aligning the positioning hole with the
(7.B) and pull out the handle (7.A).
Istruz. art. 8969100.indd 4-6
FIG. 01
Minimum
15 C° (~60F)
0.5 BAR (~7PSI)
FIG. 03
FIG. 05
FIG. 02
FIG. 06
FIG. 04
FIG. 07
P U R O
D E S I G N
I T A L I A N O
FIG. 08
26/04/11 11:10
Publicidad
