Switching On /Off, Muting; Setting The Wireless Microphone; Configuring The Wireless Microphone Via The Menu; Overview Of The Menu Settings - Monacor International JTS RU-850LTH/5 Manual De Instrucciones

Micrófono inalámbrico de mano uhf
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

5 Switching on /off, Muting

To switch on the wireless microphone, briefly
press the button
MUTE (3) from the lower to the upper position
The LED (2) next to the switch will indicate the
status of the batteries:
green = batteries are sufficiently charged
red
= batteries are almost discharged
For information with regard to the indications
on the display, please refer to chapter 1:
play (1)
To mute the wireless microphone, move the
switch MUTE
next to the switch will start flashing in green (or,
when the batteries are almost discharged, alter-
nately in red and green) and
the display To unmute the wireless microphone,
move the switch to the upper position
To switch off the wireless microphone, keep the
button
pressed until the display shows

6 Setting the Wireless Microphone

The function
ture to configure the wireless microphone on the
receiver: Make the settings on the receiver and
then simply press the button
fer the settings to the wireless microphone via
ultrasound The data sent will be received via the
ultrasonic sensor (6) of the wireless microphone
Detailed information on how to transfer data via
ultrasound can be found in chapter 8 1 of the user
instructions of the receiver Once the data have
been successfully transferred, the LED (2) on the
wireless microphone will light continuously in blue
for a few seconds and
on the display The LED will start flashing in blue
when an error has occurred during data reception
All settings for the wireless microphone can
also be made via its configuration menu
6.1 Configuring the wireless microphone
via the menu
Use the buttons SET,
menu (menu structure:
1) To call up the menu, keep the button SET
pressed for 2 seconds The display will briefly
show
, then the first menu item will be
selected
10
(5) or move the switch
to the lower position The LED
will appear on
is a most convenient fea-
will briefly appear
and
(8) to operate the
fig 1, page 2)
2) To select a menu item, press the button SET
repeatedly until the menu item has been
reached
3) To change a setting, use the button
4) To save a change, press the button SET The
display will show
be exited
Note: Setting the radio frequency requires two steps;
therefore, the setting will be saved after the second
Dis-
step (after the channel has been selected or the last
three digits of the frequency have been set)
To exit the menu without any changes, press the
button SET repeatedly until
on the display
The following chapter provides an overview of
the menu settings

6.1.1 Overview of the menu settings

The wireless microphone provides two functions
for radio frequency adjustment Adjust the radio
frequency on the microphone in the same way
as on the receiver
Menu item Setting
to trans-
Note: The order in which the two functions for fre-
quency setting appear in the menu depends on which
of them has been most recently used
Then the menu will
is briefly shown
Selecting a frequency from a group
(overview of the groups:
The group number starts flashing: Use
the button
or
to set the group; then
press the button SET.
The channel number starts flashing: Use
the button
or
to set the channel;
then press the button SET to save the
setting.
Setting the frequency directly
The first three digits of the frequency
shown start flashing: Use the button
or
to set the frequency in steps of
1 MHz; then press the button SET.
The last three digits of the frequency
shown start flashing: Use the button
or
to set the frequency in steps of
0.025 MHz; then press the button SET
to save the frequency.
or
page 3)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jts 25.9560

Tabla de contenido