Skil MASTERS 6410 Manual Original página 8

d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) maintain power tools. check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool's
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations diferent
from those intended could result in a hazardous situation.
5) SErVIcE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SaFEtY INStrUctIONS FOr Impact drIllS
• Wear ear protectors (exposure to noise can cause
hearing loss)
• Use auxiliary handle(s), if supplied with the tool
(loss of control can cause personal injury)
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory or fastener may contact hidden wiring or
its own cord (cutting accessory and fasteners
contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock)
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to ire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Always keep the cord away from moving parts of the tool
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• When you put away the tool, switch of the motor and
ensure that all moving parts have come to a
complete standstill
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• In case of electrical or mechanical malfunction,
immediately switch of the tool and disconnect the plug
• SKIL can assure lawless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
All manuals and user guides at all-guides.com
• This tool should not be used by people under the age of
• do not work materials containing asbestos (asbestos
• Dust from material such as paint containing lead, some
• Certain kinds of dust are classiied as carcinogenic (such
• Follow the dust-related national requirements for the
• If the cord is damaged or cut through while working, do
• Never use the tool when cord is damaged; have it
• Always check that the supply voltage is the same as the
• If the drill bit becomes unexpectedly jammed (causing a
• Be aware of the forces that occur as a result of jamming
• always disconnect plug from power source before
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
• If for any reason the old plug is cut of the cord of this tool,
USE
• On/of 4
• Switch locking for continuous use 5
• Speed control for smooth starting 6
• Maximum speed control 7
• Changing direction of rotation 8
• Normal drilling/screwdriving versus impact drilling 9
• Changing bits 0
• Adjusting drilling depth !
8
16 years
is considered carcinogenic)
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
materials you want to work with
not touch the cord, but immediately disconnect the plug
replaced by a qualiied person
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
sudden, dangerous reaction), immediately switch of
the tool
(especially when drilling metals); always use auxiliary
handle F 3 and take a secure stance
making any adjustment or changing any accessory
in the cord of this tool to the earth terminal of the plug
it must be disposed of safely and not left unattended
With wheel C the maximum speed can be adjusted from
low to high
- switch on the tool
- lock the switch
- turn wheel C to select maximum speed
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
! select drilling function only when tool is switched
off and plug is disconnected
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! only use sharp bits