EINHELL TC-MS 2513 L Manual De Instrucciones página 36

equipment. Never use the guards for handling
or moving the equipment.
•
Use the saw only if the guards are correctly
positioned and only if the saw is in perfect
condition and has been properly serviced.
•
When cutting miters, make sure that the
device for swiveling the arm is fastened se-
curely.
•
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
•
Make sure the workplace and the room are
sufficiently illuminated.
•
The operator must receive proper training
in the use, adjustment and operation of the
machine.
•
Use only properly sharpened saw blades
•
Check that the speed indicated on the saw
blade is at least as high as the speed indica-
ted on the saw.
•
Be sure to use only spacers and spindle rings
which are specified by the manufacturer as
suitable for the intended purpose.
•
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his
authorized agents.
•
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and not before
the saw unit is at rest.
•
Make sure that the machine is always secu-
red on a workbench or a table. Use the holes
in the machine's base frame to secure the
machine. Bolt the base frame to a workbench
or a table.
•
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of
a cut.
•
To make cuts correctly and safely:
- Always clamp the workpiece securely to the
saw table
- Each time before making a cut, make sure
that the machine stands securely
4. Additional safety instructions
•
Always pull the plug out of the power socket
before adjusting or servicing the machine.
•
Give these safety instructions to all persons
who work on the machine.
•
Do not use this saw to cut fire wood.
•
Caution! Hands and fingers may be injured on
the rotating saw blade.
•
Before you use the machine for the first time,
Anl_TC_SM_2513_L_SPK8.indb 36 Anl_TC_SM_2513_L_SPK8.indb 36
GB
check that the voltage marked on the rating
plate is the same as your supply voltage.
•
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw's power consumption.
Minimum cross-section: 1.5 mm².
•
If you use a cable reel, the complete cable
must be pulled off the reel.
•
Do not carry the saw by its power cable.
•
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allo-
wed to use the machine under supervision.
•
Keep children away from the machine when it
is connected to the power supply.
•
Check the power cable. Never use a faulty or
damaged power cable.
•
Keep your workplace clean of wood scrap
and any unnecessary objects.
•
Persons working on the machine should not
be distracted.
•
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
•
Only fit blades which are well sharpened and
have no cracks or deformations.
•
Faulty saw blades must be replaced imme-
diately.
•
Never use saw blades which do not comply
with the data specified in this manual.
•
Note the direction of rotation of the motor and
saw blade.
•
It is imperative to make sure that the arrow
(direction of rotation) on the saw blade con-
forms with the arrow on the machine.
•
Pull out the power plug and twist the blade
with your hand into the 45° and 90° positions
in order to make sure that the blade does not
touch the turntable in any position. If necessa-
ry, readjust the saw head.
•
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
•
Never wedge the hinged guard hood in open
position.
•
Never dismantle the machine's safety devices
or render them inoperative.
•
Never cut workpieces which are too small to
clamp securely on the saw table.
•
Avoid placing your hands in hazardous posi-
tions in which one or both hands could touch
the saw blade if they slip suddenly.
•
There must be no nails or other foreign bo-
dies in the workpiece.
•
Always stand to the side of the saw blade
when working with the saw.
- 36 -
15.10.15 09:50 15.10.15 09:50