Tps Theft Protection System (Optional) - Hilti TE 40 Manual De Instrucciones

CAUTION
Improve the blood circulation in your fingers by re-
laxing your hands and exercising your fingers during
breaks between working.

7.2.1 TPS theft protection system (optional)

NOTE
The power tool may be equipped with the optional theft
protection system. If the power tool is equipped with this
feature, it can be unlocked and made ready for operation
only through use of the corresponding TPS key.
7.2.1.1 Unlocking the power tool 8
1. Plug the supply cord into the power outlet. The
yellow theft protection indicator LED blinks. The
power tool is now ready to receive the signal from
the TPS key.
2. Hold the TPS key or the TPS watch strap buckle
against the lock symbol. The power tool is unlocked
as soon as the yellow theft protection indicator LED
no longer lights.
NOTE If, for example, the electric supply is briefly
interrupted due to a power failure or disconnected
when moving to a different workplace, the power
tool remains ready for operation for approx. 20 min-
utes. In the event of a longer interruption, the TPS
key must be used again to unlock the power tool.
7.2.1.2 Activation of the theft protection system for
the power tool
NOTE
Further detailed information on activation and use of the
theft protection system can be found in the operating
instructions for the theft protection system.
7.2.2 Drilling without hammering (A) 9
1. Turn the function selector switch until it engages in
the "Drilling without hammering" position. Do not
operate the function selector switch while the motor
is running.
2. Bring the side handle into the desired position and
check that it is fitted correctly and secured.
3. Plug the supply cord into the power outlet.
4. Position the power tool and drill bit at the point
where the hole is to be drilled.
5. Press the control switch slowly (drill at a low speed
until the drill bit centers itself in the hole).
6. Press the control switch fully to continue drilling with
full power.
7. Do not apply excessive pressure. This will not in-
crease the power tool's drilling performance. Lower
pressure extends the life of the insert tool.
All manuals and user guides at all-guides.com
7.2.3 Hammer drilling (B) 9
NOTE
Working at low temperatures: The hammering mecha-
nism works only when the power tool has reached a
minimum operating temperature. Bring the tip of the drill
bit or chisel into contact with the workpiece and allow
the power tool to run under no load until it reaches
the minimum operating temperature. If necessary, repeat
this procedure until the hammering mechanism begins to
operate.
1.
2.
3.
4.
5.
6.
7.
8.
7.2.4 Chiseling
NOTE
The chisel can be adjusted to 12 different positions
(in 30° increments). This ensures that flat chisels and
shaped chisels can always be set to the optimum working
position.
7.2.4.1 Adjusting the chisel (C) 9
CAUTION
Do not operate the power tool when the selector switch
is set to "Chisel adjustment".
1.
2.
3.
7.2.4.2 Locking the chisel (D) 9
Turn the function selector switch until it engages in the
"Chiseling" position. Do not operate the function selector
switch while the motor is running.
7.2.4.3 Chiseling(D) 9
1.
2.
3.
Turn the function selector switch until it engages in
the "Hammer drilling" position. Do not operate the
function selector switch while the motor is running.
Bring the side handle into the desired position and
check that it is fitted correctly and secured.
Plug the supply cord into the power outlet.
Position the power tool and drill bit at the point
where the hole is to be drilled.
Press the control switch slowly (drill at a low speed
until the drill bit centers itself in the hole).
Press the control switch fully to continue drilling with
full power.
Do not apply excessive pressure. This will not in-
crease the power tool's hammering performance.
Lower pressure extends the life of the insert tool.
Reduce drilling speed shortly before breaking
through in order to avoid damage to the surface at
the rear side.
Turn the function selector switch until it engages in
the "Chisel adjustment" position. Do not operate the
function selector switch while the motor is running.
Bring the side handle into the desired position and
check that it is fitted correctly and secured.
Rotate the chisel to the desired position.
Plug the supply cord into the power outlet.
Position the tip of the chisel at the point where
chiseling is to begin.
Press the control switch fully.
en
9