Steren PIC-500 Guia Del Usuario

Before using your new Electronic insect killer, please read
Before using your new Serial PIC microcontroller programmer, read
this instruction manual to prevent any damage. Put it away
the following recommendations.
• Do not place the programmer over metallic surfaces.
• Do not put metallic objects on the programmer.
• Before to plug or unplug a PIC from the base, you must to disconnect
the serial port from the computer.
• For circuits with 28 and 40 leads, it is necessary to buy PIC-505
• Extension.
ICPROG SOFTWARE INSTALL ON XP
1.- Place the installation disk on the CD-ROM drive.
2.- Copy the ICPROG folder to PC hard drive.
3.- Execute ICPROG program, during installation is possible that an error
message appears on screen, press Accept to continue.
4.- Once the installation finish and the program executes, open the
Settings Menu, then choose Option menu. Press on Misc eyelash and
choose Enable NT/2000/XP Driver option, the program will ask if you want
to restart the ICPROG program, click on Yes. It is possible that the system
will ask you again about Driver Installation, press Yes once again. Once
the program restarted, you'll be ready to use the ICPROG software on the
computer.
PROGRAMMING A PIC
The programming board counts with a jumper that allows you to choose
between PIC12C508 and PIC16F84, set this on the correct position.
1.- Plug the DB9 cable (male-female connectors) to an available serial port
on the computer. Plug the other end into the programmer board. (Position
1 and 2 for PIC 12C508. Position 2 and 3 for PIC 1F84).
2.- Once you have connected the cable to the board, insert the integrated
circuit on the correspondent IC socket (8 or 18 leads).
3.- Execute ICPROG program.
4.- Configure the port that you want to use.
5.- Configure the operating mode depending of the PIC.
6.- Load your program and set depending of the PIC or the memory.
7.- Go to Command menu and choose Program All, or press F5 button,
the program will ask you if you really want to program the device, with the
selected configuration (Fig. 5).
8.- If the programming was successful, then a confirmation message
appears on screen, otherwise some error messages appears after each
bar graph. This means where's the mistake.
9.- Release the programmed PIC or circuit from the board.
Before using your new Electronic i
For PIC12C508 place on the top of the board with 18 leads, next to
the base mark. Usually, place the jumper on PIC16F84 (2-3) position
for any application. Place on PIC12C508 (1-2) position exclusively for
this microcontroller model.
nsect killer, please read this instruction manual to prevent
LIST OF PICs AND MEMORIES THAT CAN BE PROGRAMMED
PIC12C5XX, 12C67X, 24CXX, 16C55X, 16C61, 16C62X, 16C71,
16C71X, 16C8X, 16F8X, 16F873*, 16F874*, 16F877*
* It is necessary to use PIC-505 Extension
Before using your new Electronic i
Product design and specifications are subject to change without
previous notice.
IMPORTANT
WARRANTY
This Steren product is warranted under normal usage against defects in
workmanship and materials to the original purchaser for one year from the
date of purchase.
1.- This warranty card with all the required information, invoice or
purchase ticket, product box or package, and product, must be
presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free
of charge.
3.- The repairing time will not exceed 30 natural days, from the day the
claim was received.
4.- Steren sell parts, components, consumables and accessories to
customer, as well as warranty service, at any of the addresses mentioned
later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God,
mishandling, leaky batteries, failure to follow enclosed instructions,
improper repair by unauthorized personnel, improper safe keeping,
among others.
a) The consumer can also claim the warranty service in the purchase
establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice
or purchase ticket.
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your
nearest dealer. If you are in Mexico, please give a call to our Call
Center.
Call Center
01 800 500 9000
Product: Serial pic microcontroller
programmer
Part number: PIC-500
Brand: Steren
CONDITIONS