Grohe Aquatower 1000 27 015 Manual Del Usuario página 6

GB
Application
In order to ensure correct operation, a pressure of at least 0.7 bar is
necessary at the shower system.
Caution:
With sufficient power, electric or gas instantaneous heaters are also
suitable.
All thermostats are adjusted at the factory at a flow pressure on both sides
of 3 bar.
Should temperature deviations exist due to special installation conditions,
the thermostat must be adjusted to the local conditions (see Adjustment).
Specifications
Minimum flow pressure
Max. operating pressure
Recommended flow pressure
Test pressure
Flow rate at 3 bar flow pressure
Hand shower
Side showers
Hand shower and side showers
Max. water temperature at hot water inlet
Recommended max. flow temperature
(energy saving)
Safety check
Hot water temperature at supply connection min. 2 °C higher than mixed
water temperature
Cold water connection
Hot water connection
If static pressure is greater than 5 bar, fit pressure reducer.
Tools required, see fold-out page I.
Delivery specification, see fold-out page II.
Installation
New installation:
Make up unions.
For union dimensions for cold and hot water connection, see fold-out
page III Fig. [1].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [2].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Retrofitting:
Union dimensions must correspond to Fig. [3].
The cold water supply must be connected on the right and the hot water
supply on the left.
The installation dimensions of the fitting relate to the standing level of the
shower stand, see Fig. [4].
The installation height of the showers from the standing level must be
observed in order to comfortably operate the fitting.
Connections and fastenings, see fold-out page III and IV, Figs. [1]
to [10].
For individual components, see delivery specification, Figs. [I] to [IV].
1.Drill fixing holes for ø 8mm mounting plugs, see Fig. [1] and [3].
2.Install accompanying elbow unions (A). If S-unions are present, remove
and replace with elbow unions (A), see Fig. [5].
3.Screw in threaded studs (A1) into the elbow unions (A) by approx. one
turn.
Seal the elbow unions (A) at the tiled wall using sealing compound.
Flush pipes thoroughly
Please pass these instructions on to the user of the fitting.
3
The right to make technical modifications is reserved.
All manuals and user guides at all-guides.com
4. Remove retaining rings (B) with installation tool (B1),
see Fig. [6].
5. Detach wall plate (B2).
6. Insert mounting plug (C1), see Fig. [7].
7. Guide elbow unions (A) through the area provided in the fitting
assembly (C) and slide rib (A2) from below behind the lug (A3) of the
elbow union, see Fig. [8].
8. Preassemble the fitting assembly (C) with the threaded studs (A1).
9. Secure fitting assembly (C) using fixings (C2) supplied, see Fig. [7].
10.Connect hoses (D) with accompanying seals (D1) and elbow
unions (A), see Fig. [9].
Spray hose, shower rail slider, shower rail and hand spray, see fold-
out page IV and V, Fig. [9], [10] and [11].
For individual components, see delivery specification, Figs. [IV], [V], [VI]
0.7 bar
and [VII].
10 bar
1.Attach spray hose (E) with seal (E1) to elbow unions (E2), see Fig. [9].
1 - 5 bar
16 bar 2.Slide shower rail slider (F) onto shower rail (F1), see Fig. [10].
3.Insert shower rail (F1) into the fitting assembly (C) and secure using
approx. 13.0 l/min
screw (F2).
approx. 12.0 l/min
4.Insert bracket (F3) onto the shower rail (F1) and secure using
approx. 21.0 l/min
screw (F4).
80 °C
5.Fit cap (F5).
If there is an offset, wall plate 45 406 special accessory can be ordered.
60 °C
6.Fit handspray (G) to spray hose (E), see fold-out page V, Fig. [11].
38 °C
Attach wall plate (B2).
1.Insert seals (B4) into the wall plate (B2), note position of seal, see detail
right
view in Fig. [12].
left
2.Slide wall plate (B2) onto the fitting assembly (C), screw on retaining
rings (B) and tighten using installation tool (B1).
Note: Keep installation tool (B1) for possible future maintenance work
on the shower system.
3.Attach rosettes (B3) to the side showers.
Operation
Operation of the shut-off handle (H), see Fig. [13]:
Shut-off handle in central position
Shut-off handle clockwise
Press button (H1) and turn
shut-off handle anti-clockwise
Press button (H1) and turn
shut-off handle anti-clockwise fully
Temperature limitation
The safety stop limits the temperature range to 38 °C.
If a higher temperature is desired, the 38 °C limit can be overridden by
pressing the button (J3), see Fig. [14].
Flow control for side shower, see Fig. [15].
= closed
= discharge from hand shower
= discharge from side shower
= discharge from side shower
and hand shower