Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOL-
LOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the
outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this
condition should be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole
means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and
unplug the Fan when not in use.
BE CERTAIN that the power source for the Fan is 120 V~ 60 Hz. DO NOT plug the Fan into 240 V~ or other power source.
The Blue Plug™ on your Lasko fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be
removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace,
repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device
incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one
way. Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety fea-
ture. If the plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
•DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire
hazard.
•ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•DO NOT block, cover or obstruct air flow to or from the fan while in operation.
•DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
•DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will not be tripped over.
•NEVER use a single extension cord to operate more than one Fan or other electrical device.
•DO NOT use this Fan if it has been damaged or is not functioning properly.
•Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
•Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural facili-
ties including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous
locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or
relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user
is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority
to operate this equipment.
•This Fan is not intended to be used by people (including children) with reduced physical, sensorial or mental capacities, or who
lack from experience or knowledge, unless they are supervised or receive instructions for the functioning of the product by a
person responsible for their safety.
•Children must be supervised to ensure they are not using the product as a toy.
SAVE THESE INSTRUCTIONS
Rev. B 11/15
All manuals and user guides at all-guides.com
2
PASO 1: ENSAMBLE DEL TUBO DE EXTENSION
1. Saque todas las partes del tubo de extensión del empaque original.
(Figura 1)
2. Afloje la Tuerca de Ajuste de Altura, girando en sentido con-
trario de las agujas del reloj. (Figura 2).
3. Eleve el tubo de extensión (Figura 3)
4. Apriete la Tuerca de Ajuste de Altura, girando en sentido de las
agujas del reloj. (Figura 4)
Tubo de Ex-
tensión
Tuerca de
Ajuste de
Altura
Figura 1
Figura 2
PASO 2: ENSAMBLE DEL PEDESTAL
COLOQUE LA BASE EN EL PISO
1. Inserte el tubo de diametro mayor en la base con un movimiento
giratorio (Figura 5). Mientras que inserta el tubo en la base, girelo
ejerciendo presion hasta que este tubo quede firmemente asentado
en la base.
2. Para ajustar la altura:
a) Afloje la Tuerca de Ajuste de Altura.
b) Eleve o baje el Tubo de Extensión hasta obtener la altura
deseada.
c) Apriete la Tuerca de Ajuste de Altura.
Tubo de Extensión
Tuerca de Ajuste de
Altura
Base
Figura 5
PASO 3: CONJUNTO DEL CABEZAL
Conjunto de
1. Coloque el Conjunto de Cabezal
con el Collar en el Tubo de
Extensión. (Figura 6)
2. Sostenga firmemente el Tubo de
Extensión y empuje el Conjunto
de Cabezal hacia abajo con un
movimiento giratorio hasta que
quede asentado en el Tubo de
Extensión.
Figura 6
2085849
Rev. B 11/15
No separe los tubos. En caso de que los tubos se llegaran a
separar, inserte el tubo A en el tubo B.
A
PASO 4: ENSAMBLE DEL ASPA Y REJILLA
1. Inclinar la Cabeza del Ventilador hacia atrás. Coloque la Rejilla
Trasera en el Conjunto de Cabezal. (Figura 7)
2. Alinear la lengüeta de la Rejilla Trasera con la ranura en la parte
superior de la cubierta delantera del Conjunto de Cabezal.
Fije los (2) tornillos No. 6 de 0.95cm de cabeza plana en los dos agu-
jeros detrás de la rejilla trasera. Es necesario un desarmador plano.
(Figura 9)
ADVERTENCIA: No apriete en exceso.
Figura 3
Figura 4
Figure 9
3. Asiente la Rejilla Trasera y sujetela con la Tuerca de Plástico
hacia la Derecha. Deslice el Aspa en el Eje del Motor.
(Figura 8) Alinee la Ranura Del Cubo de la tapa con el Pasador
del Eje del Motor. (Figura 8A)
Parrilla Trasera
Ampliar
tubo
Figura 8
Cabezal
Figura 8A
Collar
4. Para asegurar el Aspa, enrosque hasta que quede
apretada en el Cubo de la Tapa haciéndola girar hacia
la izquierda.
5. Con la cabeza del ventilador en posición vertical, coloque la
rejilla frontal alineando el ornamento en forma horizontal.
Tubo de
Asegure las rejillas insertando estas comenzando por la parte
Extensión
de abajo y siguiendo hacia arriba. LA REJILLA NO NECESITA
GANCHOS PARA SU ENSAMBLE
7
B
Conjunto
del Cabezal
Rejilla
Figura 7
Trasera
Rejilla
Aspa
Delantera
Tapa de
Tuerca de
Ventilador
Plastico
Pasador
Ranura
del Cubo
2085849
Publicidad
