3M 20233 Manual De Instrucciones página 5

Model Side Wheel
Number Handle Size
20233 NA 3"
20234 NA 4"
20243 Yes 4 1 / "
2
20235 Yes 5"
20236 Yes 6"
* Declared noise levels; measurements carried out in accordance with standard EN ISO 15744:2002.
** Declared vibration levels in accordance with EN12096; measurements carried out in accordance with standard EN ISO 8662-4;1997.
The noise and vibration values stated in the table are from laboratory testing in conformity with stated codes and standards and are not sufficient risk evaluation
for all exposure scenerios. Values measured in a particular work place may be higher than the declared values. The actual exposure values and amount of risk
or harm experienced to an individual is unique to each situation and depends upon the surrounding environment, the way in which the individual works, the
particular material being worked, work station design, as well as upon the exposure time and the physical condition of the user. 3M cannot be held responsible
for the consequences of using declared values instead of actual exposure values for any individual risk assessment.
The tool is intended to be operated as a hand held tool. It is always recommended that while using the tool, operators stand on a solid floor, in a secure position
with a firm grip and footing. Be aware that the tool can develop a torque reaction. See the section "SAFETY PRECAUTIONS".
Use a clean lubricated air supply that will give a measured air pressure at the tool of 6.2 bar (90 psig) when the tool is running with the lever fully depressed. It
is recommended to use an approved 10 mm (3/8 in) x 8 m (25 ft) maximum length airline for the 3 in. Cut-Off Wheel Tool and a 12.7 mm (1/2 in) x 8 m (25 ft)
maximum length airline for the 4 in. and larger Cut-Off Wheel Tools. Connect the tool to the air supply as shown in Figure 1. Do not connect the tool to the airline
system without an easily accessible air shut off valve. It is strongly recommended that an air filter, regulator and lubricator (FRL) be used as shown in Figure 1 as
this will supply clean, lubricated air at the correct pressure to the tool. In any case appropriate air pressure regulators shall be used at all times while operating
this tool where the supply pressure exceeds the marked maximum of the tool. Details of such equipment can be obtained for your tool distributor. If such
equipment is not used, the tool should be manually lubricated. To manually lubricate the tool, disconnect the airline and put 2 to 3 drops of suitable pneumatic
motor lubricating oil such as 3M™ Air Tool Lubricant PN 20451, Fuji Kosan FK-20 or Mobil ALMO 525 into the hose end (inlet) of the tool. Reconnect tool to the air
supply and run tool slowly for a few seconds to allow air to circulate the oil. If the tool is used frequently, lubricate it on a daily basis or lubricate it if the tool starts
to slow or lose power. It is recommended that the air pressure at the tool be 6.2 bar (90 psig) while the tool is running so the maximum RPM is not exceeded. The
tool can be run at lower pressures but should never be run higher than 6.2 bar (90 psig). If run at lower pressure the performance of the tool is reduced.
Recommended Airline
Size - Minimum
10 mm 3/8 in
12.7 mm 1/2 in
Lubricate the angle head every 6-8 working hours with premium grease with the following properties:
-High and low temperature performance
-Shear stable
-Anti-wear protection
-Low viscosity base flare for high speed application
-Very low coefficient of friction
Fuchs Renolit AX S2 or equal is recommended. Grease gun and grease available from your grease supplier.
All manuals and user guides at all-guides.com
Product Configuration/Specifications:
Speed Product Height
RPM Net WT. kg. (lb.) mm (in.)
25,000 0.95 (2.09) 76,2 (3.00)
20,000
1.02 (2.25) 82,5 (3.25)
12,000
1.49 (3.30) 133 (5.25)
12,000
1.57 (3.47) 133 (5.25)
10,000
1.67 (3.69) 133 (5.25)
Operating / Maintenance Instructions
Recommended Maximum
Hose Length
8 meters 25 feet
Length *Noise Level dBA
mm (in.) Pressure (Power)
196 (7.75) 83.5 (95.1)
196 (7.75) 83.5 (95.1)
222 (8.75) 83.5 (95.1)
222 (8.75) 83.5 (95.1)
222 (8.75) 83.5 (95.1)
Maximum Working Pressure 6.2 bar
Recommended Minimum
5
**Vibration Level **Uncertainty K
m/s 2 (ft/s 2 ) m/s 2
4.44
11.1 (36.5)
7.92
19.8 (65.1)
3.24
8.1 (26.6)
3.24
8.1 (26.6)
3.24
8.1 (26.6)
Air Pressure
90 psig
NA NA