Listening To Radio - Denon TU-201SA Instrucciones De Operación

ENGLISH
6

LISTENING TO RADIO

(1) Tuning
ON / STANDBY TIMER
MHz CH
TUNED STEREO AUTO
1 2
Example: Tuning in FM 92.50 MHz
(AM stations are tuned in using the same procedure.)
ON / STANDBY
Press the power operation
1
switch to turn on the power.
Press the BAND/RDS button on
the tuner to select the FM AUTO.
2
PRESET / TUNING
Use the PRESET/TUNING DOWN
UP/DOWN button to tune
the frequency to 92.50.
3
This lights when a station is tuned in.
8
All manuals and user guides at all-guides.com
3
The function of the UP/DOWN button on the main
unit may toggle between TUNING UP/DOWN and
PRESET UP/DOWN functions.
PRESET / TUNING
DOWN UP
• Press the MEMORY/SET button for at least 3
BAND / RDS MEMORY / SET
seconds. Then press the UP button.
The function of the UP/DOWN buttons are changed
to TUNING UP/DOWN.
AM-FM STEREO TUNER TU-201SA
• Press the MEMORY/SET button for at least 3
seconds. Then press the DOWN button. The
function of the UP/DOWN buttons are changed to
PRESET UP/DOWN.
• The UP/DOWN button is factory preset to function
as a TUNING UP/DOWN button.
However, be sure that the UP/DOWN buttons
function as the TUNING UP/DOWN button before
proceeding with step 3.
Auto Tuning
• When a program being broadcast in stereo is
received, the "STEREO" indicator lights and the
program is received in stereo.
• If reception is poor and there is much noise in the
BAND/RDS
stereo signals, press the BAND button to set the FM
MONO mode.
• When one of the TUNING UP/DOWN button is
pressed, the frequency changes in steps of 50 kHz in
the FM band, 9 kHz in the AM band.
• If one of the TUNING UP/DOWN button is held for
over 1 second, the frequency continues to change
when the button is released (auto tuning) and stops
when a station is tuned in. Tuning will not stop at
stations whose reception is poor.
UP • To stop the auto tuning function, press the TUNING
UP/DOWN button once.
NOTE:
A humming sound may be heard when using a TV
nearby while receiving AM programs. If this happens,
move the system as far from the TV as possible.
(2) Presetting AM and FM stations
Example: To preset the currently tuned in FM station at preset number "3"
2
PRESET / TUNING
DOWN
ON / STANDBY TIMER BAND / RDS MEMORY / SET
MHz CH
TUNED STEREO AUTO
AM-FM STEREO TUNER TU-201SA
1,3
MEMORY / SET
Press the MEMORY/SET button.
1
• The "MEMO" indicator
flashes.
While the "MEMO" indicator
PRESET / TUNING
DOWN UP
is flashing, press the
PRESET/TUNING UP button
three times to display "P3".
2
To store the station at a different preset
number, use the tuning buttons
(PRESET/TUNING UP or DOWN) to set the
desired preset number.
Press the MEMORY/SET button
MEMORY / SET
again while the "MEMO"
3
indicator is flashing.
• The "MEMO" indicator turns
off and the station is preset.
A total of 40 AM and FM stations can be preset
using this procedure.
When the TU-201SA is connected in a system with
the 201SA series, this operation can also be
performed on the system remote control unit (RC-
UP
906) included with the pre-main amplifier (PMA-
201SA).
When operating with the
TUNER
system remote control unit,
TAPE
first set the remote control
unit's function selector switch
to "TUNER".
Procedure
MEMORY / SET
3
/ /
TU-201SA (RC-906)
(this unit)
• This setting can also be made by pressing the
TUNING
button three times instead of pressing
"e".
• To store the station at a different preset number,
use the number buttons and the +10 button on the
system remote control unit (RC-906) to set the
desired preset number.
Examples:
To store the station at preset number 12:
Press +10 , 2
To store the station at preset number 29:
Press +10 , +10 ,
9
Presetting
• When a station is preset, both the reception
frequency and reception mode are stored in the
memory.
• If a station is preset at a number where another
station is already preset, the previous station is
erased and the new station is set.
• The preset memory is not erased immediately if the
power supply is cut off momentarily.
CD
MD
CD-R
(RC-906)
MEMORY / SET
TU-201SA
(this unit)