Diamond Drill Safety Warnings; General Safety Instructions; Battery Safety - Husqvarna DM 540i Manual De Usuario

is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
• Always start drilling at low speed and with the bit tip
in contact with the workpiece. At higher speeds, the
bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
• Apply pressure only in direct line with the bit and do
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal
injury.

Diamond drill safety warnings

• When performing drilling that requires the use of
water, route the water away from the operator's work
area or use a liquid collection device. Such
precautionary measures keep the operator's work
area dry and reduce the risk of electrical shock.
• Operate power tool by insulated grasping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
• Wear hearing protection when diamond drilling.
Exposure to noise can cause hearing loss.
• When the bit is jammed, stop applying downward
pressure and turn off the tool. Investigate and take
corrective actions to eliminate the cause of the bit
jamming.
• When restarting a diamond drill in the workpiece,
check that the bit rotates freely before starting. If the
bit is jammed, it may not start, may overload the tool,
or may cause the diamond drill to release from the
workpiece.
• When securing the drill stand with anchors and
fasteners to the workpiece, ensure that the
anchoring used is capable of holding and restraining
the machine during use. If the workpiece is weak or
porous, the anchor may pull out causing the drill
stand to release from the workpiece.
• When securing the drill stand with a vacuum pad to
the workpiece, install the pad on a smooth, clean,
non-porous surface. Do not secure to laminated
surfaces such as tiles and composite coating. If the
workpiece is not smooth, flat or well affixed, the pad
may pull away from the workpiece.
• Ensure there is sufficient vacuum before and during
drilling. If the vacuum is insufficient, the pad may
release from the workpiece.
• Never perform drilling with the machine secured by
the vacuum pad only, except when drilling
downwards.If the vacuum is lost, the pad will release
from the workpiece.
• When the drilling through walls or ceilings, ensure to
protect persons and the work area on the other side.
The bit may extend through the hole or the core may
fall out on the other side.
• When drilling overhead, always use the liquid
collection device specified in the instructions. Do not
1567 - 002 - 18.10.2021
allow water to flow into the tool. Water entering the
power tool will increase the risk of electric shock.

General safety instructions

WARNING:
instructions that follow before you use the
product.
• This product is a dangerous tool if you are not
careful or if you use the product incorrectly. This
product can cause serious injury or death to the
operator or others. Before you use the product, you
must read and understand the contents of this
operator's manual.
• Save all warnings and instructions.
• Comply with all applicable laws and regulations.
• The operator and the employer of the operator must
know and prevent the risks during operation of the
product.
• Do not let a person operate the product unless they
read and understand the contents of the operator's
manual.
• Do not operate the product unless you receive
training before use. Make sure that all operators
receive training.
• Do not let a child operate the product.
• Only let approved persons operate the product.
• The operator is responsible for accidents that occur
to other persons or their property.
• Do not use the product if you are tired, ill, or under
the influence of alcohol, drugs or medicine.
• Always be careful and use your common sense.
• This product produces an electromagnetic field
during operation. This field can under some
circumstances interfere with active or passive
medical implants. To decrease the risk of serious
injury or death, we recommend persons with medical
implants to speak to their physician and the medical
implant manufacturer before operating this product.
• Keep the product clean. Make sure that you can
clearly read signs and decals.
• Do not use the product if it is defective.
• Do not do modifications to this product.
• Do not operate the product if it is possible that other
persons have done modifications to the product.

Battery safety

WARNING:
cause an explosion and cause injury. If the
battery has a deformation or is damaged,
speak to an approved HUSQVARNA service
agent.
Read the warning
A damaged battery can
11