Mixer Operations; Basic Operations - Pioneer DJM-400 Manual De Instrucciones

MIXER OPERATIONS (BASIC OPERATIONS)

MIXER OPERATIONS

BASIC OPERATIONS

2
MIC
3
TRIM
4
HI, MID,
LOW
HEADPHONES
5
6
1. Set rear panel POWER switch to ON.
2. Set the input selector switch for the desired channel to
choose the connected component.
¶ The function of the PHONO/LINE input connectors is set using
the PHONO/LINE switch on the connection panel.
3. Use the TRIM dial to adjust the input level.
4. Use the channel equalizer dials (HI, MID, LOW) to adjust
the tone.
5. Use the channel fader lever to adjust the sound volume of
the selected channel.
6. To use the cross fader on the selected channel, set the cross
fader selector switch to either the middle position (
the right position ( ), then operate the cross fader lever.
¶ When not using the cross fader, set the cross fader selector
switch to [THRU].
7. Use the MASTER LEVEL dial to adjust the overall sound
volume.
[Selecting Stereo or Monaural]
When the connection panel's STEREO/MONO switch is set to
[MONO], the master output becomes a monaural combination of L+R
channels.
[Microphone Input]
1. Set the connection panel's MIC/AUX switch to [MIC].
2. Set the MIC switch to [ON] or [TALK OVER].
¶ When the switch is set to [TALK OVER], if sounds of over –15
dB are detected by the microphone, the output for all sound
sources other than the microphone is attenuated by 20 dB.
3. Use the MIC 1 LEVEL dial to adjust the sound volume of
MIC 1, and the MIC 2 LEVEL dial to adjust the sound
volume of MIC 2.
4. Use the microphone equalizer dial (EQ) to adjust the tone
of the microphone sound.
¶ The microphone equalizer function operates simultaneously
on microphones 1 and 2.
8
<DRB1404>
En
1 POWER
MASTER
7
MASTER
BEAT EFFECTS
LEVEL
[Auxiliary Input]
1. Set the connection panel's MIC/AUX switch to [AUX].
2. Set the MIC switch to [ON] or [TALK OVER].
3. Use the MIC 1 LEVEL dial to adjust the sound from the L
4. Use the microphone equalizer dial (EQ) to adjust sound tone.
) or
[Headphones Output]
1. Use the headphones cue button (CH-1, CH-2, MASTER) to
[Relationship of headphones cue button and headphones output]
2. Use the LEVEL dial to adjust the headphones sound level.
[Selecting the Cross Fader Curve]
The sound volume response to fader lever operation can be set to
one of two characteristic curves.
7 Use the cross fader selector switch to select the desired
[MIC]
MIC/AUX
[AUX]
MIC
3
MIC 1 LEVEL,
MIC 2 LEVEL
4
EQ
2
[PHONES]
HEADPHONES
1
CH-1, CH-2,
MASTER
2
LEVEL
THRU/
(Cross fader selector switch)
¶ The MIC1 input connector functions as AUX(L) input, and the
MIC2 input connector functions as AUX(R) input.
¶ When the switch is set to [TALK OVER], if a sound is input to
the AUX connectors, the output for all sources other than the
AUX input is attenuated by 20 dB.
channel, and MIC 2 LEVEL dial to adjust the sound from
the R channel.
select the source to be output to the headphones.
¶ The selected source button lights brightly.
Headphone cue button
CH-1 CH-2 MASTER
ON OFF OFF
OFF ON OFF
OFF OFF ON
ON ON OFF CH-1(L)+CH-2(L)
ON OFF ON CH-1(MONO)
OFF ON ON CH-2(MONO)
ON ON ON CH-1(MONO)+CH-2(MONO)
cross fader response curve.
¶ At the center position (
even, neutral rise throughout the cross fader's movement.
¶ At the right position (
rise with the cross fader's movement (sound from [2 >] is www.audiovias.com
produced as soon as the lever leaves side [< 1]).
¶ The curve settings operate the same on both sides [< 1] and
[2 >].
1
STEREO/MONO
MASTER
BEAT EFFECTS
/
Headphones Output
L channel R channel
CH-1(L) CH-1(R)
CH-2(L) CH-2(R)
MASTER(L) MASTER(R)
CH-1(R)+CH-2(R)
MASTER(MONO)
MASTER(MONO)
MASTER(MONO)
), the curve operates to produce an
), the curve operates to produce a rapid