Descargar Imprimir esta página

General Specifications; Customer Service - Klein Tools 60155 Manual De Instrucciones

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGLISH
The 60155 Cooling Fan is designed for use with Klein Tools
hard hats and safety helmets with patent-pending accessory
mounts, for easy attachment and removal. Its dual-fan
design forces outside air into the shell to push out stale hot
air, facilitating cooling. Included user-replaceable ducts can
be changed to direct air to cool the neck and face region, as
well.The user can configure the system 16 different ways,
depending on their preference. It is powered by a detachable,
modular, rechargeable lithium-ion battery (Catalog no.
29025) which can also be used to charge other small USB
powered devices.
CONTENTS
• Cooling Fan
• Rechargeable Modular Battery
• Long Duct With Clip (×2)
• Long Duct Without Clip (×2)
• Short Duct With Clip (×2)
• Short Duct Without Clip (×2)
• USB-A to USB-C charging cable
• USB-C to USB-C charging cable
• Cable Clip
• This Instruction Sheet

GENERAL SPECIFICATIONS

COOLING FAN
Configuration: Centrifugal Dual Fan
Dimensions: 6.2" × 2.8" × 3.0" (157.5 × 71.1 × 76.2
mm)
Weight (fan only): 6.88 oz. (195 g)
Runtime (on fully-charged battery, continuous use):
High: 3.5 hours Low: 6 hours
Drop Protection: 6.6' (2 m)
Ingress Protection (IP) Rating: IPX4
BATTERY
Dimensions: 3.5" × 1.7" × 2.1" (88.9 × 43.2 × 53.3 mm)
Weight (battery only): 3.85 oz. (109 g)
Cell Type: 18650 Lithium-Ion
Capacity: 3200mAh (11.7 Wh)
Input USB-C (each): 5V DC, 1.1A
Input USB-C (total): 5V DC, 1.1A
Output USB-C (each): 5V DC, 1.0A (1800 mAh) up to 2A
Max
Output USB-C (total): 5V DC, 1.0A (1800 mAh) up to 2A
Max
Total Output Power: 10 W Max.
Full Charge Time: Up to 2.5 hours, based on charger
output
Shelf Life: Charge every 3 months
Charging Requirements: 5V DC, Min. 1A
recommended
Operating/Charging Temperature: 32° to 104°F (0° to
40°C)
Storage Temperature (up to 3 months): 14° to 104°F (-10° to
40°C)
Relative Humidity: <75% non-condensing
Drop Protection: 6.6' (2 m)
Ingress Protection (IP) Rating: IP54
Standards: UN38.3, DOE/CEC, NRCAN
Conforms To UL STD. 2054, 1642, 62368-1,
UL STD. 507, UL SUBJECT 2056
Certified To CSA STD. C22.2 NO. 62368-1,
CSA STD. C22.2 NO. 60335-1, 60335-2-80
5014132
Specifications subject to change.
DISPOSAL / RECYCLE
Do not place equipment and its accessories in the
trash. Items must be properly disposed of in
accordance with local regulations. See www.epa.
gov/recycle for additional information.

CUSTOMER SERVICE

KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069
1-800-553-4676
customerservice@kleintools.com
www.kleintools.com
WARNINGS
Read, understand, and follow these instructions to ensure safe
operation. Failure to observe these warnings can result in risk
of fire and burns, electric shock, serious injury and/or property
damage. Always check with your site safety supervisor before
use of this product. Local regulations may not permit use. Keep
this user manual and comply with the instructions provided for
this product.
COOLING FAN
• This product is ONLY intended for use with Klein Tools hard
hats and safety helmets with accessory mounts designed to
securely keep the modular cooling fan and battery provided.
• DO NOT use any other cables, batteries, or ducts not
designed for use with this device. Refer to the user manual
for proper charging instructions. Replace ONLY with Klein
Tools replacement parts.
• Inspect daily. DO NOT use the product if damaged.
• DO NOT subject to vibration, impacts, or drops. The housing
may not show signs of damage, but internal components
may have been compromised. It is advisable to replace the
unit if any such severe events occur.
• DO NOT expose to open flame, heat sources, equipment that
produces heat or vibration, or extremes in environmental
temperature.
• DO NOT expose product to rain or snow.
• Keep away from high voltage devices.
• DO NOT attempt to repair the fan, charging cable, and ducts.
There are no user-serviceable parts.
• DO NOT immerse in water or other liquids. Avoid spilling
liquids or falling foreign objects into openings on the enclosure.
• DO NOT open, crush, or incinerate.
• Water-resistant port cover must be properly sealed to achieve
specified water & foreign object ingress protection. Keep seal
free of dirt, oil, sand, or other material that interferes with
proper sealing. Failure to do so can result in risk of fire or
electric shock.
• DO NOT open water-resistant cover if wet or in a wet
environment. Thoroughly dry the unit and the seal around
water resistant cover completely before opening water-
resistant cover.
• DO NOT attempt to insert other USB connector types into USB-C
port.
• Use of cable not recommended or sold with this unit may
result in a risk of fire or injury to persons.
BATTERY
• Only use the battery in the applications per manufacturer's
recommendations. Consult the instruction manual if unsure.
• Always charge and discharge the battery using the charging
accessories recommended or provided by the manufacturer.
The charger used shall comply with IEC 62368-1, PS2
power source. If charging accessories are damaged,
DO NOT use or attempt to repair the cables and replace
immediately. There are no user-serviceable parts.
• DO NOT attempt to charge or power any device with this
battery without verifying if battery and device are compatible.
Consult the user manuals for requirements for each.
• DO NOT charge or discharge the battery in excess of its
rating. Overloading above rating may result in a risk of fire
or injury to persons.
• In the event the battery leaks, keep away from skin and eye.
If exposed, wash affected area with large amounts of water
and seek medical attention.
• DO NOT use a damaged or modified battery. Damaged
or modified batteries may exhibit unpredictable behavior
resulting in fire, explosion or risk of injury.
• DO NOT subject to vibration, impact, or drops. The housing
may not show signs of damage, but internal components
may have been compromised. It is advisable to replace the
unit if any such severe events occur.
• DO NOT expose battery to extreme heat or cold, rain or
snow, or fire.
• Keep away from high voltage devices.
• Keep battery out of reach of children. Children should be
supervised when battery is in use.
• Risk of fire and burns. Do not open, crush, heat above 140°F
(60°C), or incinerate. Follow all manufacturer's instructions.
• Dispose battery properly in accordance with local regulations.
SYMBOLS ON COOLING FAN AND/OR BATTERY
Warning or Caution
Risk of Electrical Shock
Read Instructions
Recyclable
Independently tested by Intertek and meets
applicable standards.
Energy Efficiency Verified
FEATURE DETAILS (FIG.A)
1
Battery Status Button
2
Battery Release Tab
3
Battery Status LED Indicator
4
USB-C Input/Output Ports (×2)
5
Accessory Mount For Headlamp
6
Accessory Mount
7
Duct Ports (×2)
8
Removable Grille (×2)
9
Cooling Fan Release Tab
10
Power On/Off / Speed Button
11
USB-C Power Input Port
12
Short Duct With Clip (×2)
13
Short Duct Without Clip (×2)
14
Long Duct With Clip (×2)
15
Long Duct Without Clip (×2)
16
USB-C to USB-C 2.0 Cable
17
USB-C to USB-A 2.0 Cable
18
Cable Clip
19
Grille Release Tabs (×2)
COMPLIANCE
FCC & IC COMPLIANCE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged totry
to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
NOTE: The grantee is not responsible for any changes or
modifications not expressly approved by the party responsible
for compliance. Such modifications could void the user's
authority to operate the equipment.
Canada ICES-003 (B) / NMB-003 (B)
BASED ON: 1390430 Rev 04/21 A (2 of 12)

Publicidad

loading