Before Using The Equipment; Practical Tips - EINHELL 44.651.60 Manual De Instrucciones

rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before using the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
Charge the battery pack with the charger.
5.1 Fitting the plug-in tools (Figures 1-5)
•
Open the quick-release lock for changing
tools (5) as shown in Fig. 2.
•
To fit the plug-in tools safely you should
hold the multifunction tool so that the On/Off
switch (1) points down and the tool chuck (2)
faces up.
•
Place the plug-in tool (e.g. the scraper) on
the tool chuck (2) so that the pins of the tool
chuck fit into the recesses in the plug-in tool.
The tool chuck (2) is magnetic in order to
secure the plug-in tool during the clamping
procedure.
•
Close the quick-release lock for changing
tools (5) again. Take care that the pins of the
chuck (2) remain in the recesses in the plug-
in tool.
•
The equipment comes with a disk (14) for
safely securing plug-in tools with recesses.
Please note the correct use (camber facing
the tool) of the disk (14) for plug-in tools with
recess as shown in Fig. 4 and 5.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The hook-and-loop-fastener enables easy chan-
ging of the abrasive paper. Make sure that the va-
cuum extraction holes on the abrasive paper and
the grinding/sanding disk are aligned.
6. Operation
6.1 Charging the LI battery pack (Fig. 6/7)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (7) downwards
Anl_Varrito_SPK13.indb 17 Anl_Varrito_SPK13.indb 17
GB
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.2 Switching on and off (Fig. 8)
Slide the switch (1) forwards to switch on the
equipment.
Slide the switch (1) to the rear again to switch off
the equipment.

6.3 Practical tips

•
Switch on the equipment.
•
Work away from the body.
•
Never move your hands into the direct vicinity
of the work area.
•
Use only plug-in tools which are in good wor-
king order and undamaged.
- 17 -
26.07.2021 08:36:06 26.07.2021 08:36:06