Main Connection; Compressed Air Connection - SCHEU BIOSTAR Manual De Instrucciones

G
English
4. Info menu
The following information is given in the info menu:
Software: Display of the installed firmware version
Safety instructions: Here you'll find important instructions on the safe usage of your pressure moulding device.
Indications: Discover the variety of applications in the digitised version of the application booklet „pressure moulding technique".
Guideline to solve technical problems: Find quick and easy solutions to problems in the working process.
Range of pressure moulding material: Get an overview in the wide range of pressure moulding material and information on each kind of material.
Videos: Update your knowledge watching our short videos on the fabrication process of various kinds of pressure moulded splints.
By pressing the button „info" T the info menu can be called up. The machine has to be in the basic position (pls. refer to point 7).
You can navigate through the system pressing the following buttons:
The LEDs at the buttons indicate that information is available.
Info button T:
Calling up the info menu
Hint!
After having scanned pressure moulding material, only specific information on this kind of material will be available. The info menu is not
available and disappears during the pressure moulding process (heating/pressurising/cooling). Hints and instruction on the pres-
sure moulding process are considered with priority and appear on the display, as soon as infrared heater, pressure chamber or
locking ring are moved from the basic position.
r and R buttons: The horizontal navigation keys are only available after having called up an „indication" and enable you to navigate through the
various „indications".
OK button : Confirming the selection.
22
qandQbuttons: The vertical navigation keys will lead you through the actual menu.
-Button : By pressing the back button, you'll return to the previous selection.
21
CE+home button: By pressing the button „CE+home", you'll return to the display: „material selection depending on indication".

5. Main connection

Connect the BIOSTAR machine to the corresponding network by plugging in the original power cable on the back of the machine 7, (please also
®
refer to connection to the local network in the safety instructions). Two fuses are built in to protect the machine from high voltage (230 V version).
To exchange the fuses press the little clip below the connector 8 and take off the fuse. For the 100 V/115 V versions, these fuses are built in two
separate fuse covers R, which can be unscrewed.

6. Compressed air connection

A 20 bar tube 9 with filter element is fixed to the back of the machine and should not be exchanged. Connect the BIOSTAR
sure system. Use the 20 bar tube and optionally a quick connect coupling. The working pressure is set up at 6 bar/87 psi and should not be changed
as it is calibrated to achieve the best pressure moulding results.
However, if you wish to lower the working pressure, just adjust it by using the pressure regulator J on the back of the machine. Before turning the
regulator, pull to release it (
Adjust the pressure by turning the regulator and push it in afterwards. If the pressure exceeds 6.5 bar/94 psi the security valve will be set into action.
(depressurisation noise).
7. Basic position
Infrared heater 1 is swivelled back to the stop, pressure chamber 2 is opened to the left, locking ring handle 3 is swivelled back to the stop
(12 o'clock position). Please refer to fig.1
8. Switching on
Press the ON/OFF button M, allow the machine 10 seconds to set itself up before using. Now the display shows the standard dialogue which is the
starting point for any pressure moulding operation. Programming is done through display O or sanner P and shown in the display N.
9. Positioning of blanks
All round blanks and foils with a diameter of 125 mm and a thickness of 0.1 to 5.0 mm can be pressed in the BIOSTAR
chamber 2 by swivelling to the left side, take off the locking ring K by turning it in 5 o'clock position. Place the material directly on the 0 ring in
the pressure chamber. Put on the adjustment ring L, so that the bayonet clamps slip under the bevel of the locking device of the chamber. Tighten
by turning clockwise into 6 o'clock position.
).
machine to the air press-
®
machine. Open the pressure
®