Triton TCMBS Instrucciones De Uso Y De Seguridad página 6

Product Familiarisation
1. ON/OFF Switch
2. ON/OFF Switch Lock
3. Main Handle
4. Micro Adjustment Knob
5. Front Belt Roller
6. Drive Roller
7. Belt Tension Release Lever
8. Belt Direction Indicator
Accessories (not shown):
• 1 x Dust Extraction Adaptor
• 3 x Sanding Belts (80, 100, and 120 grit
Intended Use
Palm belt sander for intricate, light to medium duty sanding on soft and hard woods and similar
materials.
The tool must ONLY be used for its intended purpose. Any use other than those mentioned in
this manual will be considered a case of misuse. The operator, and not the manufacturer, shall
be liable for any damage or injury resulting from such cases of misuse. The manufacturer shall
not be liable for any modifications made to the tool, nor for any damage resulting from such
modifications.
Unpacking Your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
Changing the sanding belt
WARNING: Always ensure that the tool is switched off and the plug is removed from the power
point before fitting or removing sanding belts.
Note: A range of sanding belts from Triton, in a choice of grits, are available for use with this
Palm Belt Sander.
1. Ensure the sander is disconnected from the power supply
2. Lift the Belt Tension Release Lever (7) to release tension on the belt
3. Choose a new belt according to intended task, e.g. low grit rating produces faster stock
removal, high grit rating for smoother finish
4. Check that the replacement belt has a good join and is not frayed at the edges
5. Position the new belt over the rollers, with the rotation arrows on the inside of the belt pointing
in the same direction as the Belt Direction Indicator (8) on the sander.
6. Push the Belt Tension Release Lever down to tension the belt
7. Hold the sander upside down and plug into the mains
8. With the belt running, use the Micro Adjustment Knob (4) to align the belt to the centre of
the plate
Dust extraction
• It is recommended that the sander is connected to a vacuum cleaner or dust extractor, using
the dust extraction port (Image A). This will significantly reduce the dust in the air around
the work area
• If vacuum dust extraction is not available in your work area, a dust bag can be fitted to the
dust extraction port.
• A suitable breathing mask should be worn when operating this machine. All wood and paint
dust is hazardous to health and may also be toxic.
Operation
Switching ON & OFF
WARNING: Always hold the sander securely by the Main Handle (3).
WARNING: Ensure the sander is not in contact with the surface when the machine is
EN
switched on.
1. Slide the ON/OFF Switch (1) all the way forward into the ON position and hold in position
(Image B)
2. Press the ON/OFF Switch Lock (2) from either side, all the way in (Image B)
3. Release the pressure on the ON/OFF Switch, which now remains locked in the ON position
4. To switch the tool OFF, slide the ON/OFF Switch forward until the ON/OFF Switch Lock
automatically disengages
5. Release the ON/OFF Switch
6
475114_OwnerManual_04AUG21.indd 6 475114_OwnerManual_04AUG21.indd 6
Sanding
WARNING: Do not apply too much pressure on the sander. Pushing down too hard may
cause damage or reduce the life of the product.
WARNING: Keep hands away from the belt, as it will continue to move for a short time after
the machine is switched off.
• Apply light pressure when the sander is brought into contact with the workpiece
• Allow the sander to reach full speed before moving it across the workpiece
• To remove paint or smooth very rough wood, sand across the grain at 45° in two directions
and then finish parallel with the grain (Image C)
• Use the Front Belt Roller (5) only to sand corners or irregular shapes (Image D)
• Lift the sander clear of the workpiece before switching OFF
Accessories
• A range of accessories, including a variety of different grade sanding sheets, is available
from your Triton dealer. Spare parts can be purchased from your Triton dealer or online at
www.toolsparesonline.com
Maintenance
• This tool is manufactured using class-leading components and makes use of the latest in
intelligent circuitry that protects the tool and its components. In normal use it should provide
a long working life
Cleaning
• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear quickly,
and shorten the machine's service life. Clean the body of your machine with a soft brush or
dry cloth. If available, use clean, dry, compressed air to blow through the ventilation holes
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: tritontools.com/en-GB/Support
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
De Keten
00004
5651 GJ
Eindhoven, Netherlands
Storage
• Store this tool and its accessories after use in its case, in a dry, secure place out of the reach
of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE),
with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of
power tools
04/08/2021 13:04 04/08/2021 13:04