Product Overview; Product Use; Product Maintenance - YATO YG-07001 Manual De Instrucciones

GB

PRODUCT OVERVIEW

The beverage dispenser is used for short-term storage and distribution of beverages. The dispenser should not be used to store
and distribute carbonated beverages. Proper, reliable and safe operation of the product depends on appropriate use, that is why
you should:
Read and keep the entire manual before the fi rst use of the product.
The supplier shall not be held liable for any damage or injury resulting from improper use of the product, failure to observe the
safety regulations and recommendations of this manual. Use of the product for purposes other than those for which it was intend-
ed shall cause the loss of the user's rights to the guarantee and under warranty.

PRODUCT USE

Unpack the product by removing all packaging components. Before fi rst use, product maintenance must be carried out in accord-
ance with the instructions under "PRODUCT MAINTENANCE".
The tank is equipped with a column for fi lling with ice cubes in case the beverage needs to be cooled. Insert the column into the
tank so that the lower edge is fi xed in the fl ange at the bottom of the tank. The upper part of the column should be passed through
the opening in the frame inside the tank. The column fi xed in this manner will not tip over during use of the product. Ice should be
put into the column keeping the ice level below the column's upper edge.
If ice is not required, there is no need for using the column.
Place the dispenser in the beverage distribution spot and then fi ll the product with the beverage. Fill the tank via the top edge after
removing the lid. Leave a free space of approx. 3 cm between the beverage level and the top edge of the tank.
CAUTION! Do not pour hot drinks into the tank - the temperature of the beverage must not exceed 60 C.
O
Empty the tank using the tap at the bottom of the tank. Tilting the tap lever will begin pouring the beverage from the tank. Releasing
the pressure on the lever will automatically return the lever to vertical position. In this position the tap valve is closed.
CAUTION! The lever can be locked in a 90-degree, tilted position. This is only possible if the lever is tilted in one direction. It is
recommended to check this function before fi lling the tank.

PRODUCT MAINTENANCE

Due to the intended use of the product for the storage of beverages for consumption, the maintenance of the product should be
carried out carefully. This will help to maintain proper hygiene. Maintenance of the product should be carried out after each use, i.e.
each time after removing the beverage from the tank. Do not leave the beverage in the tank. Prolonged contact with the beverage
may cause discolouration of the tank's plastic parts. Maintenance of the tank after each emptying will prevent discolouration and
the build-up of beverage sediments.
Use only mild kitchen cleaning agents to clean the product. It is not allowed to use abrasive cleaning agents, e.g. cleaning powder
or milk, or agents containing corrosive substances. Do not use any solvents, petrol, or alcohol to clean the product.
The cleaning agent should be applied in accordance with the instructions supplied with the product, then applied to the soft cloth
with which the product should be cleaned inside and outside.
Remove the cleaning agent residue from the outside with a soft cloth soaked in water, then wipe dry. Rinse the interior of the
product with clean water and dry or leave it to dry.
After cleaning, fi ll the tank with at least 1 litre of clean water, then open the valve and empty the contents of the tank. This will
remove beverage residues from the inside of the valve.
CAUTION! The tank is not designed for water jet cleaning. Do not immerse the product in water or other liquid. Do not wash the
tank in a dishwasher.
The removable stainless steel parts of the product: the tank lid, column frame, column, drip tray and the drainer can be cleaned
in the same manner as the tank or in a dishwasher. Clean the remaining parts of the casing in the same manner as the tank.
CAUTION! Before pouring a new beverage, the tank should be completely emptied with the previous beverage residue removed.
In particular, beverages of diff erent kinds should not be mixed. Mixed beverages can react with each other, which can lead to
clogging of the valve.
O R I G I N A L I N S T R U C T I O N S
3