AneX Q1 SPORT Manual Del Usuario página 14

STROLLER
ASSEMBLING / DISASSEMBLING.
Unbox this stroller's frame and put it horizontally on the
floor (fig. 1). Disable the lock against accidental unfolding
EN
(fig. 2). Pull upwards vigorously till the system is secured,
while holding the handle (you should hear a specific sound)
(fig. 3, 4). To fold the frame, press the red button located on
the frame's right lever. Then simultaneously pull the levers
located on both sides of the frame (fig. 5). Gently push the
frame down to the original position it had when you were
unpacking this stroller (fig. 1). This stroller features a handle
for carrying or transporting this stroller's frame (fig. 6).
For easy carrying or transporting the frame turn the handle
through 90° (fig. 7).
HANDLE HEIGHT ADJUSTMENT
Simultaneously press the round buttons, placed in parallel on
both sides of the handle. Set a comfortable handle height for
you (fig. 7).
MOUNTING / DISMOUNTING
OF THE REAR WHEELS
Before mounting a wheel, insert an axis pin, while holding
the red button (fig. 8). Release the button to secure this axis
pin (you should hear a specific sound); To mount a wheel,
press the wheel's center button, then push it along the axis
pin till it stops, release the button and push gently until it
locks (fig. 9). To dismantle a wheel, press down its midpoint
and pull along the axis pin till it comes off completely. (fig. 9).
A wheel is dismounted without the axis pin, but the axis pin
can be removed as well by pressing the red button (fig. 8).
INSTALLATION / REMOVAL
OF THE FRONT CASTER WHEELS / LOCK
The stroller's frame is equipped with two front caster wheels,
assembled with a fork, and revolving 360° around its axis.
To install front wheels, you have to insert the fork axle into
the wheel. Next, press the axle with the fork until you hear a
distinctive sound. To dismount a front wheel, vertically press
the button located above this wheel. A wheel is dismounted
together with its axis pin (fig. 10). If you want to lock the
All manuals and user guides at all-guides.com
PRE-USE PROCEDURES
caster wheel system, turn the controller, which is located
below the button for their removal (fig. 11). In addition,
you can move the stroller only forward and sideways on
unlocked wheels. You can not push the stroller back. This
prevents curving the frame and loosening the wheels.
BRAKE
This stroller features a parking brake blocking its rear wheels
(fig. 12). To stop this stroller, you must press the pedal
blocking rear wheels (fig. 12). To continue moving along, you
need to reset the pedal (fig. 12).
SHOCK ABSORPTION
The stroller has a steel-ring shock absorption system and
adjustable shock absorption on the frame to improve your
baby's comfort (fig. 13, 14). To adjust the frame-based shock
absorption mechanism, turn both regulators (right and left)
in the same direction depending on the type of road (soft /
hard mode). The spring shock absorption mechanism
is regulated using a special switch located under the shock
absorber (fig. 13). Always adjust both sides equally.
PORTABLE CRADLE
MOUNTING / DISMOUNTING
To mount the portable cradle, place the adapters into the
adapter pockets, located on the frame's inner side (fig. 15).
The portable cradle adapters are blocked automatically;
To dismount the portable cradle, press the buttons
of the portable cradle adapters, while lifting it up (fig. 15).
If necessary, you can remove the bassinet's lining for
washing (fig. 16, 17). To do this, you have to lift the bassinet's
backrest and then carefully remove the lining by unzipping
two zippers. Besides, you have an option of removing and
washing the coconut mattress protector. The bassinet's
backrest is located under the coconut mattress. You can
adjust the backrest's height using the controller, which is
located below the bassinet (fig. 18).
PORTABLE CRADLE HOOD,
FEET COVER
The portable cradle features a conveniently foldable hood
protecting a child from wind, sun, snow and rain elements.