Wall Mounting; Intended Use; Assembly And Adjustments - DeWalt DCM849 Manual De Instrucciones

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.

Intended Use

The DCM849 heavy-duty polisher is designed for polishing
painted or unfinished metal, fiberglass, and composite
surfaces in professional applications. Common examples
of use include but are not limited to: auto/marine/RV/
motorcycle detailing and finish correction, boat construction
and repair, and metal or concrete finishing.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Handles
Attaching Auxiliary Handle (Fig. A)

WARNING: Before using the tool, check that the
handle is tightened securely.
Screw the auxiliary handle 7
on either side of the gear case. The auxiliary handle should
always be used to maintain control of the tool at all times.
Installation of the Bail Handle Assembly
(Fig B)
1. Place the bail handle
12
aligning the screws 13 with the threaded holes and
the ears on the gear case with the slots in the bail
handle assembly.
2. Tighten the screws with the supplied hex wrench to
secure the handle to the polisher.
Adjustment of the Bail handle Angle (Fig. B)
1. Loosen both screws
13
2. Rotate the bail handle
12
position making sure that the detent groves align.
3. Re-tighten the screws to secure the handle to
the polisher.
tightly into one of the holes
over the polisher gear case
2 full turns.
to the desired 45˚ or 90˚
Fig. B
12
Wool Ingestion Shields (Fig. A)
The wool ingestion shields 10
amount of wool, dust, and debris that gets ingested by the
motor during normal use. The goal of the ingestion shields
is to improve durability as compared to a unit without the
ingestion shields.
Each ingestion shield can be easily removed for cleaning by
slipping a finger or coin underneath the removal recess and
pulling to release the cover.
The wool ingestion shields can be cleaned with soap and
water and a soft bristle brush in the event they get clogged
with polish and debris. Clean the shields as soon as you start
to see buildup on the outside.
Your tool may come with a set of wool ingestion shields.
The wool ingestion shields are available at extra cost from
your local dealer or authorized service center.
Soft Rubber Gear Case Cover (Fig. A)
The soft rubber gear case cover
metal gear case scuffs on painted or polished surfaces.
The soft rubber gear case cover can be removed if required.
To take off the cover, remove the three mounting screws
and lift the cover over the gear case.
Your tool may come with a soft rubber gear case cover. The
soft rubber gear case cover is available at extra cost from
your local dealer or authorized service center.
Attaching and Removing Polishing Pads
(Fig. C, D)

WARNING: To reduce the risk of serious personal
injury, do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely. Tuck
away or trim any loose attachment strings. Loose and
spinning attachment strings can entangle your fingers
or snag on the workpiece.
Polishing pads with a diameter of 7" (180 mm) may be used
with the DCM849.
nOTE: The DCM849 may use either type of polishing pad
assembly described below.
To Attach Polishing Pad with Rubber
Backing Pad (Fig. A, C)
1. To attach polishing pad
14
washer through the hole in the center of the
15
polishing pad as far as it will go.
English
13
are designed to reduce the
9 is designed to eliminate
, push the hub of the clamp
9