Scope Of Delivery - Weka KS30 Instrucciones De Funcionamiento

4.2

Scope of delivery

KS30 -
KS30S -
KS30E -
Accessories -
5. P R E P A R A T I O N
Make sure that the drill rig has not been damaged during transport. Check if all components are at hand.
Screw the 3 handles of the hand wheel (20) into the shaft center up to marking.
Lock for all works on the rig, in working breaks and while not on use, the feed. Therefore clamp the fixing
brake (19). For drilling loosen the fixing brake (19) so far, that the hand wheel can be moved easily. Hold
the hand wheel, for avoiding an uncontrolled down sliding of the drilling machine.
5.1 Assembling the diamond core drill (see images A and B)
Feed slide (16) and quick connect plate (13) can only be connected in one position with each other (see
image B). The quick change plate has a shape, the machine reception of the feed slide a corresponding
cut-out.
Put the quick connect plate (13) on the core drill in that way, that the parallel keys (12) engage into the
corresponding cut-out of the gear foot of the core drill. Screw the quick connect plate and the core drill
together with the four hexagon socket screws (11) which are included in delivery.
Loosen the eccentric bolt (14) with the hand wheel (20) and pull it out of the feed slide (16) as far as it will
go. Hang the drilling machine with the quick connect plate (13) into the machine reception in that way,
that the lower nose of the quick connect plate is behind the lower bolt of the machine reception (see
image A).
Clap the drilling machine onto the machine reception and put the eccentric bolt (14) back in. Tighten the
eccentric bolt (14) with the hand wheel (20) (the eccentric bolt clamps clockwise as well as anti-
clockwise).
For loosening the core drill proceed the other way round.
For the WEKA diamond core drill SR25 there is alternatively a quick connect plate available with part no.
KS30745.2. When using this quick connect plate holes of 300mm up to 350mm diameter can be drilled
without an additional distance plate.
5.2 Distance plate for holes 300 - 350 mm (see image C)
For holes of 300 mm to maximum 350 mm diameter the distance plate (31) must be inserted additionally
on the WEKA drill types DK26 and DK32. Therefore put the quick connect plate (13) in that way on the
distance plate (31) that the parallel keys (12) of the quick connect plate engage into the corresponding
channels on the distance plate. Then put the distance plate (31) including quick connect plate (13) on the
core drill in that way, that the parallel keys of the distance plate engage into the channels of the core drill.
Insert the four screws (32) of the distance plate and tighten these with a hexagon socket wrench. Then
mount the drilling machine and described above on the drill rig.
5.3 Fixing the drill rig
The drill rig can depending on the surface of the underground be fixed with dowels, vacuum or a quick
bracing column.
5.3.1 Fixing with dowels
Use only suitable steel dowels, resp. anchors with a drilling diameter of at least 16 mm and a thread bars
of at least M12. Therefore consider the requirements of VDMA. Take care that the dowel is absolutely
tight and the required tear out force are not exceeded.
Insert a concrete dowel with expansion key (27) resp. a masonry dowel. Screw the quick clamping spindle
(28) into the dowel. Put the machine as well as a washer (29) on and screw these on with the split nut
(30).
Drill rig with aluminum foot (1), guide rails (6) steel rolls (18), swivel foot set (2), star
handle (20), operators manual.
like drill rig KS30, but with steel foot, operators manual
Drill rig with aluminum foot (1), plastic rolls; without stop bolt, swivel foot set, guide
rails and level for horizontal leveling
Distance plate (31), Vacuum adaptor (25), water collection ring (21)
9