Product Features - HMDX SoundSpa Sunrise Manual De Instrucciones

IB-HX5500EU-0211-01.qxd:Layout 1 9/2/11
• If the adaptor sustains damage, you must stop using this product immediately and contact
the HoMedics Service Center. (See the warranty section for the HoMedics address.)
Caution: All servicing of this product must be performed by authorized
HoMedics Service Personnel only.

PRODUCT FEATURES:

• Dawn simulator using your own lamp
• 6 Nature Sounds: Rain Forest, Ocean, Thunder, Summer Night, Rain and Water Fall
• AM/FM radio with alarm and snooze
• Seven gentle-wake options – lamp only, lamp and nature sound, lamp and beep, lamp and
radio, nature sound only, radio only, or beep only
• Easy-to-read clock with blue LED display
• Projection feature projects time on the ceiling in a soothing blue light
• Auto-timer lets you choose how long you listen – 15, 30, 45 or 60 minutes or continuously
• Volume control adjusts the volume of the radio, beep or nature sounds
• Wireless lamp brightness control
RADIO
TIMER
ALARM SET
ALARM MODE
VOLUME
SNOOZE BUTTON
Figure 1
RAIN FOREST
OCEAN
THUNDER
Figure 2
07:55 Page 4
LAMP CONTROL
PROJECTOR
BUTTONS
TUNER
POWER BUTTON
DISPLAY
WATER FALL
RAIN
SUMMER
NIGHT
Figure 3
4
INSTRUCTIONS FOR USE:
1. Unpack the product and check to make sure everything is included (Fig. 1).
2. This unit is powered by a DC adaptor, which is included.
3. The battery power is designed only to provide MEMORY BACK-UP for the clock and alarm
settings. One 9 Volt battery (not included) should be inserted into the battery compartment if
memory back-up is desired (in the event of power outages or if the unit is unplugged).
However, the time will not be illuminated on the clock display. As soon as the power supply
returns, the display will indicate the correct time.
NOTE: Battery must be installed in order for clock memory back-up to operate. In the event of
a power failure or disconnection, if the battery is not installed, the clock and alarm will need to
be re-set when power is restored.
4. To install battery, remove compartment cover from the bottom of the unit. Insert one 9 Volt
battery into the compartment following the diagram. Replace cover and snap into place.
5. Attach the DC adaptor connector to the jack located on the back of the unit (Fig. 4) and insert
the adaptor into a 230V household outlet.
6. To use the dawn simulator and to control your lamp from your SoundSpa Sunrise, plug your
lamp into the wireless receiver (Fig. 3). Then plug the wireless receiver into a 230V
household outlet.
NOTE: Consult lamp instructions for light bulb specifications. The SoundSpa Sunrise works
with most lamps that use incandescent or CFL dimming light bulbs. Before purchasing CFL
bulbs verify they can be used in lamps with dimming switches.
Setting the Clock
1. Your SoundSpa Sunrise clock is set to a 12 hour clock. If you would prefer a 24 hour clock,
press the 12/24 button once (Fig. 4).
2. Press and hold the HOUR button for 2 seconds (Fig. 4). The time will begin to flash
3. While the time is flashing, press the HOUR button until you reach the correct hour. Then press
the MINUTE button (Fig. 4) until you reach the correct minute.
NOTE: PM indicator will appear on the left side of the clock face for evening hours (Fig. 7). If
the PM indicator is not illuminated, the hour is set to AM. Be sure to set the time for the
correct 12-hour period – AM (morning) or PM (evening).
NOTE: After 5 seconds, the time will stop flashing and it will be set.
4. Press the BACKLIGHT HI/LO button (Fig. 4) to choose between high and low clock LED
display brightness.
Listening to Nature Sounds
1. Select the sound you wish to listen to and press the corresponding button (Fig. 2).
2. To adjust the volume, turn the VOLUME knob (Fig. 1) to your desired level.
3. When finished listening to the sounds, you may turn them off by pressing the POWER button,
or switch to the radio by pressing RADIO (Fig. 1).
NOTE: When the unit is turned on, it will always default to the last mode used.
Listening to the Radio
1. Press the RADIO button (Fig. 1).
2. Rotate the TUNER (Fig. 1) to select a radio station.
3. To adjust the volume, turn the VOLUME knob (Fig. 1) to your desired level.
4. When finished listening to the radio, you may turn it off by pressing the POWER button, or
switch to a nature sound by pressing the corresponding button (Fig. 1 and 2).
NOTE: To change between bands, there is an AM/FM switch located on the back of the unit
(Fig. 4). When FM band is selected, a FM Indicator will appear on the left side of the clock
face (Fig. 7). If the FM indicator is not illuminated, the band is set to AM.
5