IB-HX5500EU-0211-01.qxd:Layout 1
9/2/11
Using the Lamp
1. To turn the lamp on, press the lightbulb
2. To increase the brightness of the lamp, press and hold lightbulb
is reached.
3. To turn the lamp off, press the lightbulb
4. To dim the lamp, press and hold lightbulb
5. You may also turn the lamp off by pressing the POWER button once. Pressing the POWER
button again will turn the lamp on (Fig. 1).
NOTE: If radio is on it will mute during lamp adjustment resuming when adjustment
is complete.
Using the Auto-Timer
When the power is ON and you are listening to a nature sound, the radio, or have your lamp
illuminated through the SoundSpa Sunrise wireless receiver, you may set an auto off timer so the
sound and/or light will automatically fade to off in the last 5 minutes of the chosen time.
1. Toggle through the TIMER button (Fig. 1) to find the time of your choice 15, 30, 45 or 60
minutes shows on the clock face. The TIMER indicator will appear on the left side of the clock
face to confirm that it is set (Fig. 7).
2. The time remaining on the auto-timer can be terminated at any time by pressing the POWER
button to turn off the nature sound, radio or lamp (Fig. 1)
Setting and Using the Alarm
For more information see Fig. 8.
1. Press the AL SET button (Fig. 1) and the time will flash.
2. While the time is flashing, press the HOUR button until you reach the correct hour. Then press
the MINUTE button until you reach the correct minute (Fig. 4).
NOTE: When digits are flashing, press and hold the HOUR or MINUTE button continuously for
a fast advance (Fig. 4).
NOTE: The PM function applies to the alarm. If the PM indicator is not displayed on the clock
face, the alarm will be set to AM. (Fig. 7).
3. Press AL SET button to set the time, or after 5 seconds the alarm will be set automatically
(Fig. 1).
4. To activate the alarm you may choose one of 7 settings. To confirm your setting, the appropriate
alarm indicators will be illuminated on the clock face to the right of the time (Fig. 7).
a) LAMP-push the AL MODE button once. To set the Sunrise mode, adjust the 15/30/OFF
switch (Fig. 4) to set lamp to brighten gradually in 15 or 30 minutes or in the OFF position
to set lamp to turn on to full brightness at the set alarm time (Fig. 1).
b) NATURE SOUND-push the AL MODE button twice. The nature sound will be the last
sound you listened to. To change the nature sound press the nature sound button you
wish (Fig. 2) and then press POWER button (Fig. 1).
c) RADIO-push the AL MODE button 3 times (Fig. 1). Use the tuner to adjust the radio to your
desired station (Fig. 1).
d) BEEP-press the AL MODE button 4 times (Fig. 1).
e) LAMP & NATURE SOUND-press the AL MODE button 5 times (Fig. 1).
f) LAMP & RADIO-press the AL MODE button 6 times (Fig. 1).
g) LAMP & BEEP-press the AL MODE button 7 times (Fig. 1).
07:55
Page 6
once (Fig. 1).
until desired level
once (Fig. 1).
until desired level is reached.
6
5. When the alarm sounds, the corresponding alarm indicator (Lamp, Sound, Radio, Beep or
combination of these) blinks. You may take the following actions:
a) SNOOZE-press the SNOOZE button (Fig. 1). The SoundSpa Sunrise wake feature will be
activated in 9 minutes. See Fig. 8 for options. You may use this feature until you turn the
alarm off.
b) RESET-turn the alarm off by pressing ANY button but the SNOOZE button (Fig. 1).
The alarm clock will automatically reset for the next day in its current mode. The
corresponding ALARM indicator (Lamp, Sound, Radio, Beep or combination of these) will
indicate this. If you wish to change the wake mode, follow step 4 under Setting and Using
the Alarm.
c) OFF-to completely turn off the alarm continue to press the AL MODE button until all the of
the alarm indicators (lamp, sound, radio, beep) are off (Fig. 1).
Note: If alarm sounds for 30 minutes continuously it will automatically turn off and reset for
the next day.
Figure 4
BACKLIGHT HI/LO
12/24
HOUR
MINUTE
PROJECTOR
ON/OFF
Figure 5
TIME PROJECTION ANGLE
Figure 6
AM/FM
DC JACK
15/30/OFF
FOCUS KNOB
TIME
ROTATION
KNOB
7