Technical Specifications - Skil 504 Instrucciones

GB
Leveling laser
INTRODUCTION
• This tool is intended for the defi ning and checking of
exact horizontal and vertical lines and all angles in
between by means of leaser beam projection
• Carefully read this instruction manual as well as the
warning label on the tool, before you use the tool 1
• Pay special attention to the safety instructions and
warnings; failure to follow these may result in
serious (eye) injury
• Save this instruction manual for future reference

TECHNICAL SPECIFICATIONS

Laser type
Laser class
Power output
Power supply
Estimated battery life
Operating temperature
Storage temperature
Accuracy
Weight
TOOL ELEMENTS 3
A On/off switch
B Battery compartment cover
C Scrolling wheel
D Magnetic base
E Laser light opening
F Bubble levels
G Warning label
H Leveling plate
J Alignment pin
K Adjustment knobs
L Tripod base
SAFETY
• Do not look into the laser beam (laser radiation) 2
• Do not point the laser beam at persons or animals
• Do not place the tool in a position that may cause
anyone to look into the laser beam intentionally or
unintentionally
• Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to view
the laser beam
• Do not remove or damage the warning label on the tool
• Do not operate the tool in the presence of fl ammable
liquids, gases or dust
• Do not operate the tool with children around
• This tool should not be used by people under the age of
16 years
SKIL_IB0504db_v2.indd 9 SKIL_IB0504db_v2.indd 9
504
650 nm
2
< 1 mW
2x AA (LR6) / 1,5V battery
40 hours
0ºC to 40°C
-10ºC to 50°C
+/- 1 mm/m
0,37 kg
9
• Do not use the tool for any purpose other than those
mentioned in this instruction manual
• Only use the original accessories which are intended for
this tool
• Always switch off the tool when not in use
USE
• On/off 4
- switch on/off the tool on by pushing switch A
downwards/upwards
! do not look into the laser beam
! do not point the laser beam at persons or animals
! always switch off the tool after use
• Mounting of batteries 5
! ensure that the tool is switched off
- remove cover B by turning it counter-clockwise
- insert 2 x AA (LR6) / 1,5V batteries (pay attention to
correct polarisation)
- mount cover B by turning it clockwise
- always remove the batteries from the tool, if the tool
is not used for a long period
- always replace the complete set of batteries
• Operating the tool 6
- project a horizontal/vertical line by moving wheel C
completely to the right/left (ensure that the bubbles in
both levels F are centered)
- project a line under an angle from 0° to 90° by
moving wheel C in either direction until the laser line
has reached the desired angle
- obstructions in front of the tool will not affect the line
projection 7
- use the tool manually for quick reference of a straight
line or alignment of two points of reference 8
- use leveling plate H for leveling the tool when placed
on a surface
• Projecting lines using leveling plate H 9
- mount the tool on leveling plate H by using alignment
pin J
- position the tool with plate on any fl at surface in such
a way that a horizontal or vertical line is projected on
the object in front of you (= reference line)
- level the tool by turning adjustment knobs K in such
a way that the bubbles in both levels F are centered
! check the leveling after each movement of the
tool
- make measurements using the projected line as
reference 0
- vertical lines will be projected from any angle as long
as the bubbles in both levels are centered
- horizontal lines will be projected from any desired
height as long as the bubbles in both levels are
centered
• Magnetic base D 9
- for easy mounting the tool on leveling plate H
- for mounting the tool on any ferrous metal surface or
profi le
• Aligning objects horizontally on adjacent walls !
• Aligning objects vertically on adjacent surfaces @
10-01-2008 10:40:23 10-01-2008 10:40:23