Auxiliary Handle - Worx WU330 Manual Del Usuario

OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
1.CHANGING THE DRILL CHUCK (See A)
(WU330.2)
• Removing the Replacement Drill Chuck
WARNING: Before removing the
replacement drill chuck, always
remove the tool or bit!
With the drill pointing toward you, grasp the
locking ring (7) of the SDS-plus "quik-change"
chuck and pull forward firmly, then rotate it to
the side.The SDS-plus "quik-change" chuck
will come free.
• Attaching the Replacement Drill Chuck
When mounting the precision keyed chuck
(12), grasp the precision keyed chuck with
the whole hand, push it as far as it will go,
then rotate it to the side until it can clearly
be heard to latch.The precision keyed chuck
locks itself. Check locking by pulling on the
precision keyed chuck. Make replacements in a
corresponding manner.
2. INSERTING/REPLACING THE DRILL
CHUCK (SEE FIG. C)
• Inserting the Drill Chuck
To work with tools without SDS-plus (e.g.,
drills with cylindrical shafts), a suitable drill
chuck must be used. Insert the adapter (14) of
the drill chuck (13) with a twisting motion into
the SDS-plus chuck (10) until it can be heard to
lock.The adapter locks itself. Check the locking
by pulling on the drill chuck.
• Removing the Drill Chuck
To remove the drill chuck (13), pull the locking
sleeve (8) to the rear, hold in this position and
remove the drill chuck from the tool holder.
3. INSERTING AND REMOVING DRILL BIT
IN SDS
Take care that the dust protection cap (9)
is not damaged when changing tools.
• Inserting
Clean and lightly oil the bit before inserting.
Insert the dust-free bit into the bit holder with
a twisting motion until it latches.
Rotary hammer
M-13L-WU330WU330.1WU330.2WU332-070225-·¨ÓïCE´¦ÐÞ¸Ä.indd 9
All manuals and user guides at all-guides.com
The bit locks itself. Check the locking by pulling
on the tool.
• Removing
Retract back the bit holder locking sleeve (8)
and pull out the bit.
to get your job done quickly and effectively.
These forces may cause inferior quality
SDS bits to break and jam in the chuck, We
therefore recommend that only high quality
SDS bits be used with this tool.
4. MOUNTING OF BIT IN KEYED CHUCK
(WU330.1/WU330.2/WU332.1)
chiseling!
Before mounting the drill bit, attaching the 13
mm keyed chuck, insert bit between the chuck
jaws as far as it will go. Ensure drill bit is in
the center of the chuck jaws. Using the chuck
key provided, there are three holes in which
the chuck key should be inserted.Tighten them
equally in turn at each of the three holes, not
just at one hole.Your drill bit is now locked in
the chuck.The bit can be removed by reversing
the above procedure (See B).
5. ON/OFF SWITCH WITH VARIABLE
SPEED CONTROL
Depress to start and release to stop your tool.
This tool has a variable speed switch (1) that
delivers higher speeds with increased trigger
pressure - speed is controlled by varying the
pressure applied to the switch (See D)
6. SWITCH LOCK-ON BUTTON
Depress the on/off switch (1) then the lock on
button (2) (See D); release the on/off switch
first and the lock-on button second.Your switch
is now locked on for continuous use.To switch
off your tool just depress and release the
on/off switch.

7. AUXILIARY HANDLE

Slide the handle onto the drill and rotate to
the desired working position.To clamp the
auxiliary handle rotates the handle clockwise.
WARNING!Your new WORX Rotary
Hammer Drill generates powerful forces
WARNING: Do not use tools without
SDS-plus for hammer drilling or
9
EN
2007-3-13 9:28:19