COMEM eSDB 10 Manual De Instrucciones página 37

1 2 3
M16x1.5 PLUG
C
1
D
A
Figura 9
E
ADVERTENCIA
2
F
Entre el tapón y la carcasa debe colocarse una junta para evitar
B
1 2 3
cualquier fuga.
El sistema (tubo y tapón) debe estar montado para garantizar la
estanqueidad.
eSDB-15/30/40
Primer paso: Retire la cinta/tapa de plástico de las zonas
C
de aire de entrada/salida. Fije la brida superior (Fig. 10/A)
en la brida del tubo desde el conservador (Fig. 10/B) con
cuatro tornillos M12 (Fig. 10/C).
PRECAUCIÓN
D
Ponga la junta plana entre las dos bridas.
B
E
A
F
Figura 10
1
Segundo paso: Compruebe el nivel superior (Fig.16/17/
18/19/E), la burbuja interna debe estar dentro del anillo
negro más pequeño.
Tercer paso: desenrosque el tornillo inferior en la parte
inferior del dispositivo (Fig. 11/A) hasta el final del rango
de trabajo de los tornillos.
4 5 6
M16x1.5 PLUG
2 3
LAST REVISION
AGGIORNATO DISEGNO - Drawing updated
DESCRIPTION
TOLLERANZE GENERALI SECONDO - GENERAL TOLERANCES ACCORDING TO ISO 2768
MATERIAL
- - -
PROCESS
- -
CREATED BY REVIEWED BY
Diego Boro -
3 APPROVED ON DOCUMENT KIND 4
- Component Drawing
1
COMPANY TITLE / SUPPLEMENTARY TITLE
CONNECTION ESDB10
COMEM
RESPONSIBLE DEPARTMENT -
ITABB-9AAE306693
DOCUMENT ID
NE-286
© COPYRIGHT ALL RIGHTS RESERVED
4 5 6
A
B
C
D
E
F
1
2 3
7 8
A
B
C
Figura 11
4
CREATED BY
Diego Boro
D
APPROVED ON
-
COMPANY
El fabricante del transformador puede elegir si aplica el kit COMEM
RESPONSIBLE DEPARTMENT
antivibración que se suministra con el eSDB en función de la
ITABB-9AAE306693
REPLACED
E
REVISION
m
SCALE NO
robustez del soporte (fig. 12/A). Para las conexiones eléctricas
WEIGHT - kg
-
PART NUMBER
-
COMEM aconseja utilizar cables armados.
APPROVED BY
-
BASED ON DOC ID WORK ORDER ID PROJECT ID 5
3
2
F
STATUS REV ITER SHEET
A
Development
3 1/1
7 8
DRAWING SHEET ISO 5457: 1999-A3T
Figura 12
C
2 3
4
5
NOTA
REVIEWED BY
-
DOCUMENT KIND
Component Drawing
TITLE / SUPPLEMENTARY TITLE
COMEM ESDB10
-
DOCUMENT ID
NE-1188
© COPYRIGHT ALL RIGHTS RESERVED
6
4 5
A
CREATED BY
Diego Boro
CREATED BY APPROVED ON
-
Diego Boro
COMPANY
APPROVED ON COMEM
-
RESPONSIBLE DEPARTMENT
ITABB-9AAE306693
COMPANY TITLE / SUPPLEMENTARY TITLE
COMEM ESDB10
COMEM
-
RESPONSIBLE DEPARTMENT
4 5
ITABB-9AAE306693
DOCUMENT ID
5
A
6 7
APPROVED BY
-
BASED ON DOC ID WORK ORDER ID
STATUS REV
A
Development
7 8
6
DRAWING SHEET ISO 5457: 1999-A3T
REVIEWED BY
-
REVIEWED BY DOCUMENT KIND
Component Drawing
-
TITLE / SUPPLEMENTARY TITLE
COMEM ESDB10
DOCUMENT KIND
Component Drawing
-
DOCUMENT ID
NE-1188
© COPYRIGHT ALL RIGHTS RESER
6
NE-1188
© COPYRIGHT ALL RIGHTS RESERVED
6 7
37
PROJECT ID
ITER SHEE
2 1/1
7
APPROVED BY
-
BASED ON DOC
7
STATUS
Develop
DRA