AneX cross city Manual De Funcionamiento página 19

STROLLER
ASSEMBLING / DISASSEMBLING
Unbox this stroller's frame and put it horizontally on the
floor (fig. 1). Disable the lock against accidental unfolding
(fig. 2). Pull upwards vigorously till the system is secured,
while holding the handle (you should hear a specific sound)
(fig. 3, 4). To fold the frame, press the red button located
on the frame's right lever. Then simultaneously pull the
levers located on both sides of the frame (fig. 5). Gently
push the frame down to the original position it had when
you were unpacking this stroller (fig. 1). For efficiency and
convenience, the frame can be folded together with the
seat without removing the seat unit from the frame (fig. 1).
For easy carrying or transporting the frame turn the handle
through 90° (fig. 6).
HANDLE HEIGHT ADJUSTMENT
Simultaneously press the round buttons, placed in parallel on
both sides of the handle. Set a comfortable handle height for
you (fig. 6).
WHEEL MOUNTING / DISMOUNTING
OF THE REAR WHEELS
Before mounting a wheel, insert an axis pin while holding the
red button (fig. 7). Release the button to secure this axis pin
(you should hear a specific sound). To mount a wheel, press
the wheel's center button, then push it along the axis pin till
it stops. Release the button and push gently until it locks
(fig. 8). To dismantle a wheel, press down its midpoint and
pull along the axis pin till it comes off completely (fig. 8).
A wheel is dismounted without the axis pin. However, the
axis pin can be removed as well by pressing the red button
(fig. 7).
INSTALLATION/REMOVAL OF
THE FRONT CASTER WHEELS/LOCK
The stroller's frame is equipped with two front caster wheels,
assembled with a fork, and revolving 360° around its axis.
To install front wheels, you have to insert the fork axle into
the wheel. Next, press the axle with the fork until you hear a
distinctive sound. To dismount a front wheel, vertically press
the button located above this wheel. A wheel is dismounted
together with its axis pin (fig. 9). If you want to lock the
caster wheel system, turn the controller, which is located
below the button for their removal (fig. 10).
All manuals and user guides at all-guides.com
PRE-USE PROCEDURES
BRAKE
This stroller features a parking brake that blocks its rear
wheels (fig. 11). To stop this stroller, you must press the
pedal that blocks the rear wheels (fig. 11). To continue
moving along, you need to reset the pedal (fig. 11).
SHOCK ABSORPTION
The stroller has a steel-ring shock absorption system and
shock absorption on the frame to improve your baby's
comfort. The spring shock absorption mechanism is
regulated using a special switch located under the shock
absorber (fig. 12). Always adjust both sides equally.
SEAT UNIT MOUNTING / DISMOUNTING
To mount the seat unit, place its adapters into the adapter
pockets located on the frame's inner side (fig. 13). The seat
unit's adapters are blocked automatically; To dismount the
seat unit, press the buttons of the seat unit's adapters, while
lifting it up (fig. 13). The seat unit's backrest can be adjusted
to the desired height using the adjuster located on the seat's
backside (fig. 14).
SEAT UNIT HOOD, FEET COVER
The seat unit features a conveniently foldable hood
protecting a child from wind, sun, snow and rain elements.
The hood position is adjusted by pressing on its top
(fig. 15). The seat unit features a feet cover, which is secured
with buttons on both sides in this stroller's forepart (fig. 16).
This stroller features a rain protection system and insect
protection (fig. 17). The seat unit's hood can be ventilated by
unfastening a zipper on the roof and untucking the bottom
part (fig. 18).
FOOTREST ADJUSTMENT
For adjusting to the desired height, simultaneously press the
buttons located in front of each other on both sides of the
footrest (fig. 19).
SEAT UNIT'S SECURITY BARRIER
Every seat unit features a security barrier with a protective
mechanism preventing a child from getting out of this stroller.
Simultaneously press the red buttons, placed in parallel on
both sides of the handle, set a comfortable height for your
EN