Vertical Steam Ironing; Auto-Off Function; Care And Cleaning; Troubleshooting - Breville VIN411X Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 21

Vertical steam ironing

Vertical steam ironing is especially useful for ironing items such as curtains while they
are hanging, or jackets, suits and coats.
Once the temperature indicator light
w
the iron in a vertical position and press the steam trigger
Warning: Hot steam is emitted from the soleplate. Do not iron/steam a
garment whilst wearing it. Do not operate steam in the direction of yourself or
anybody else.

Auto-off function

The iron has an auto-off safety function that will operate when your appliance has not
been used for 5 mins. The unit will enter a sleep mode and all the lights will turn off. To
restart simply pull the steam trigger
r
to reheat to the desired temperature, which will be indicated by the pulsing temperature
indicator light
.
w

Care and cleaning

Warning: Do not use harsh abrasives, chemical cleaners or solvents to clean
the exterior of your iron.
Allow your iron to completely cool down and wipe the soleplate with a soft damp cloth. If
polyester has burnt to the soleplate, iron a damp cotton cloth while your iron is still hot.
Wipe over the rest of your iron with a soft damp cloth then wipe dry. Do not immerse the
appliance or power cord or plug in water or any other liquid.
Self-cleaning
Only activate the self-clean when you want to activate the self-cleaning
system. Never activate the self-clean function when ironing.
The self-clean function removes scale and impurities. The steam generator has an
intelligent reminder cleaning mode which activates after continuous steam ironing over
a total of 25 hours. If you are in a hard water area you can perform the cleaning cycle
sooner than the allocated 25 hours by following the steps below.
The cleaning indicator light
will illuminate to remind users to clean the machine.
q
1.
To activate the self-clean function, press and hold the self-clean button
3 seconds. The clean indicator light will flash. Place the iron handset
cleaning tray
and pull the steam trigger
d
handset, this will initiate the cleaning function.
2.
Hot water and steam will be ejected from the holes in the soleplate along with any
impurities. During the cleaning process there is no need to hold the product.
3.
The cleaning cycle takes approximately 1 minute. When the clean indicator light
stops flashing, the cleaning cycle is complete, and you can switch off your unit
and store when cooled.
4.
To cancel the self-clean function, press and hold the self-clean button for 3
seconds. The clean indicator light will stop flashing.
WARNING: Do not attempt to pick up the handset while the clean indicator
light is flashing as hot water and steam may be ejected. Only remove from the
cleaning tray once the clean indicator light has stopped flashing and you have
switched off the power. Always use the cleaning tray provided and do not leave
unattended during the clean cycle.
8
VIN411X_20MLM2 (EU).indd 8-9
VIN411X_20MLM2 (EU).indd 8-9
turns solid, your product is ready to use. Hold
as required.
r
. The unit will restart and may need a short time
q
e
once then remove hands from the
r

Troubleshooting

Issue
The iron does not
produce steam.
Brown particles
are emitted from
the soleplate
No display lights
are showing.
for
on the
For further troubleshooting and FAQs visit www.breville.co.uk/faqs
After sales service and replacement parts
In the case the appliance does not operate but is under warranty, return the product
to the place it was purchased for a replacement. Please be aware that a valid form of
proof of purchase will be required. For additional support, please contact our Consumer
Service Department at: United Kingdom: 0800 028 7154 | Spain: 0900
81 65 10 | France: 0805 542 055. For all other countries, please
call +44 800 028 7154. International rates may apply. Alternatively,
e-mail: BrevilleEurope@newellco.com.
Root cause
Possible solution
Water tank level is too low.
Fill water tank.
Your steam generator will
beep twice, and the power
indicator light will flash to let
you know that the water tank
needs filling.
Water tank is not fully inserted
Remove and re-insert the
to the base station. Check if
water tank until an audible
power light is flashing.
click is heard.
If it is on first use the unit may
Operate the steam boost a
have not been primed.
few times by double-clicking
the steam trigger in quick
succession.
The unit is still heating up.
Wait until the temperature
The steam will only operate
indicator light stops flashing
when the temperature
and turns to solid.
indicator light is solid. Check if
light is flashing.
The handset needs to be
Operate the self-clean
de-scaled.
process. Follow instructions
provided in "Self-cleaning"
section.
Steam generator has not used
Pull the steam trigger. Unit
steam function for 5 minutes
should come out of auto-off
and entered auto-off mode.
mode. You may need to wait
a short time for unit to heat
up before it can produce
steam. When the temperature
indicator light turns solid the
unit is ready for use.
9
4/22/20 10:40
4/22/20 10:40

Publicidad

Tabla de contenido
loading

Tabla de contenido