Technical Data - Gardena EasyCut 400/25 Instrucciones De Empleo

5. Pull the plastic ring h back over the filament cassette
g
6. Reinstall the filament cassette
"Replacing the filament cassette".
Problem Possible Cause
The trimmer no longer cuts Filament worn or too short.
The trimmer no longer cuts Filament cassette empty.
Filament drawn into the
cassette or stuck together.
Filament cannot be The filament became too dry
and brittle (e. g. over the winter).
extended or filament
is consumed rapidly
Frequent contact between the
filament and hard objects.
NOTE: For any other malfunctions please contact the GARDENA service depart-
ment. Repairs must only be done by GARDENA service departments or specialist
dealers approved by GARDENA.

7. TECHNICAL DATA

Turbotrimmer Unit Value (Art. 9807)
Motor power consumption W 400
Mains voltage /
V / Hz 230 / 50 – 60
Mains frequency
Filament thickness mm 1.6
Cutting width mm 250
Filament supply
m 6
Filament feed Tip mechanism
Rpm of filament cassette
rpm 12,000
(approx.)
Weight (approx.)
kg 2.9
Telescopic adjustment of
cm 24
the turn handle (approx.)
Sound pressure level L 80
1)
dB (A)
pA
Uncertainty k 3
pA
Sound power level L :
2)
WA
measured/guaranteed 92 / 95
dB (A)
Uncertainty k 3
WA
Hand/arm vibration a 3
3)
m/s
2
vhw
Uncertainty k 1.5
a
Measuring process complying with: DIN EN 60335-2-91
1)
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of
exposure. The vibration emission value can vary during actual use of the electric power
tool.
8. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty:
In the event of a warranty claim, no charge is levied to you for the services
provided.
GARDENA Manufacturing GmbH offers a two-year warranty (effective
as of the date of purchase) for this product. This warranty includes all
significant defects of the product that can be proved to be material or
manufacturing faults. This warranty is fulfilled by supplying a fully functional
replacement product or by repairing the faulty product sent to us free of
charge; we reserve the right to choose between these options. This ser-
vice is subject to the following provisions:
• The product was used for its intended purpose as per the recommen-
dations in the operating instructions.
• Neither the purchaser nor a third party has attempted to repair the
product.
This manufacturer's warranty does not affect warranty entitlements against
the dealer / retailer.
All manuals and user guides at all-guides.com
g .
as described under 5. MAINTENANCE
Remedy
v Lengthen the filament
(see 3. OPERATION "Filament
feed – Tip mechanism" ) .
v Replace the filament cas sette
(see 5. MAINTENANCE
"Replac ing the filament
cassette") .
v Pull the filament out of the
filament cassette (see above).
v Place the filament in water
for approx. 10 hours.
v Avoid contact between the
filament and hard objects.
RL2000/14/EG DIN EN 786.
2) 3)
If problems arise with this product, please contact our Service depart-
ment or send the defective product along with a brief description of the
fault to GARDENA Manufacturing GmbH, making sure to have sufficiently
covered any shipping costs and to have followed the relevant postage
and packaging guidelines. A warranty claim must be accompanied by
a copy of the proof of purchase.
Consumables:
The filament cassette and cassette cover are consumables and are not
covered by the guarantee.
9