Cleaning And Maintenance; Troubleshooting - Royal Catering RC-CGE22 Guia Del Usuario

EN
4. Place the ground coffee container or place the
coffeemaker portafilter on the handle (8).
5. Press the microswitch (10) with sufficient force. The
engine will start and the coffee beans will be ground
after a while. Loosen the handle, grinding will stop.
6. Turn the power off (6) after use.
3.4. DEVICE USE RC-CGM20
1. Turn the power switch on to start the engine. Check if
the power light is on.
2. Set the grinding degree ring to your preference
(before adding coffee beans).
• The desired grinding degree of the coffee should
be set between 1 and 19, with 1 being fine and 19
being coarse.
• If the grinding degree is unsuitable, press the
part (7) downwards and at the same time turn the
grinding degree ring (3). The coffee powder will
be coarser when turned clockwise and finer when
turned counter-clockwise. Adjust the grinder
according to your preferences.
3. Pour coffee beans into the funnel and put the cover
on.
4. Place the ground coffee container or place the
coffeemaker portafilter on the handle (8).
5. Press the microswitch (10) with sufficient force. The
engine will start and the coffee beans will be ground
after a while. Loosen the handle, grinding will stop.
6. Turn the power off (6) after use.
3.5. DEVICE USE RC-CGM21
1. Turn the power switch on to start the engine. Check if
the power light is on.
2. Set the grinding degree ring to your preference
(before adding coffee beans).
• The desired grinding degree of the coffee should
be set between 1 and 19, with 1 being fine and 19
being coarse.
• If the grinding degree is unsuitable, press the
part (7) downwards and at the same time turn the
grinding degree ring (3). The coffee powder will
be coarser when turned clockwise and finer when
turned counter-clockwise. Adjust the grinder
according to your preferences.
3. Pour coffee beans into the funnel and put the cover
on.
4. Place the ground coffee container or place the
coffeemaker portafilter on the handle (8).
5. Operate the buttons on the control panel as shown on
fig. 1.
The SET button is used to set the time. After pressing
the SET button, the time will flash on the panel, which
means the time can be set.
Press (A) for a single cup or press button (B) for a
double cup. Use the (+) (-) buttons to set the time
required to grind a single cup or two cups, then press
the SET button to complete the setting. Press button
(C) once to start continuous grinding and press it
again to stop grinding. When pressing button (C)
for the first time, the grinder will run for a further 60
seconds.
10
C
A B
6. Turn the power off after use.
3.6. DEVICE USE RC-CGE22
1. Turn the power switch on to start the engine. Check if
the power light is on.
2. Set the grinding degree ring to your preference
(before adding coffee beans).
• The desired grinding degree of the coffee should
be set between 1 and 19, with 1 being fine and 19
being coarse.
• If the grinding degree is unsuitable, press the
part (7) downwards and at the same time turn the
grinding degree ring (3). The coffee powder will
be coarser when turned clockwise and finer when
turned counter-clockwise. Adjust the grinder
according to your preferences.
3. Pour coffee beans into the funnel and put the cover
on.
4. Place the ground coffee container or place the
coffeemaker portafilter on the handle (8).
5. Touch the Double or Single buttons on the keypad
and press the microswitch (10) with appropriate force.
The engine will run for as long as it has been set.
Touch the relevant buttons to stop grinding.
Control panel: Touch button (A) to display the default
time for a single cup. Touch the button (B) to display
the default time for a double cup.
To change the default time for a single cup, hold
down the button (C) for 3 seconds until the SET on
the display turns red and flashes. Then press button
(A) for a single cup and button (C) until SET on the
display turns red and the S and Single units flash,
which means that you can set the time for a single
cup. Touch the (+) and (-) buttons to increase or
decrease the default time, then touch the (C) button
to automatically save the time set for a single cup.
To change the default time for a double cup, hold
down the button (C) for 3 seconds until the SET on
the display turns red and starts flashing. Then press
button (B) for a double cup and button (C) until
SET on the display turns red and the S and Double
units flash, which means that you can set the time
for double cups. Touch the (+) and (-) buttons to
increase or decrease the default time, then touch the
(C) button to automatically save the time set for the
double cup.
6. Turn the power off after use.
Rev. 20.05.2021

3.7. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used.
• Wait for the rotating elements to stop.
b) Use only mild, food-safe detergents to wash the
device.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e) Do not spray the device with a water jet or submerge
it in water.
f) The device must be regularly inspected to check its
technical efficiency and spot any damage.
g) Use a soft, damp cloth for cleaning.
h) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
i) Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils or
other chemical substances because it may damage
the device.
If you need to disassemble certain parts of the device, make
sure that the power switch is turned off or pull the plug
from the socket to avoid touching the switch by mistake
and starting the device.
Cleaning the inner surface of the grinding chamber:
1. Dismantle the funnel and the cover.
2. Turn the scale regulator (grinding degree ring)
upwards clockwise.
3. Remove the blade holder.
4. Clean the inside surface.
Grinding chamber assembly:
1. Assemble the blade holder.
2. Turn the scale regulator (grinding degree ring)
counterclockwise until it is in the desired position.
3. Assemble the funnel and the cover.
* Carefully remove the coffee powder from the base
and the threads of the scale adjustment knob,
otherwise the grinding degree of the ground coffee
may be affected. The scale knob may get stuck, which
cannot be turned when reassembled, or can only be
turned partially.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with
their markings. By choosing to recycle you are making
a significant contribution to the protection of our
environment. Contact local authorities for information on
your local recycling facility.
Rev. 20.05.2021
EN

TROUBLESHOOTING

POSSIBLE
PROBLEM SOLUTION
CAUSE
Replace the power switch.
Turn the power off,
then clean the grinding
chamber. Check if there
are no foreign objects
obstructing the engine and
preventing it from running.
After checking, reinstall all
parts. Operate the starter
Power
for a test after confirming
switch
that all parts are properly
damage
assembled.
If the power switch is not
damaged, check if the
indicators on the control
panel are on (for (RC-
CGM21) and (RC-CGM22)
devices). If the control panel
The
does not work, it must be
engine
replaced.
cannot
turn on
Replace the fuse.
Turn the switch off and
then clean the grinding
chamber. Check if there
are no foreign objects
obstructing the engine and
preventing it from running.
After checking, reinstall all
Blown parts. Operate the starter
fuse for a test after confirming
that all parts are properly
assembled.
If the fuse is not damaged,
check if the control panel
indicators are on (for (RC-
CGM21) and (RC-CGM22)).
If the control panel does not
work, replace it.
The parts
inside the
grinding
Disassemble and reinstall all
chamber
parts carefully.
are not
fitted
correctly.
Clean and preserve the
grinding chamber according
The scale
Inaccurate
to the operating instructions,
adjuster
grinding
and then reassemble.
(grinding
Turn the power switch on
degree
and slowly slide the scale
ring) is
adjuster to the right until
not turned
you hear the grooved
clockwise
disc rubbing. Then turn it
towards
counterclockwise about 0,5
the positi-
cm. After completing the
oning bar.
above steps, add coffee
beans for a trial grinding.
11