Before Use
• Do not mash hard or uncooked food, as this may
damage the unit.
• Peel and remove any stones or hard parts; cook
and drain then mash the fruit/vegetable.
Assembly and Operation
• Fit the gearbox (9a) to the shaft (9b) by turning in
a clockwise direction until it locks into place.
• Turn the puree accessory upside down and fit the
paddle (9c) over the central hub and turn
counter- clockwise to locate. (If the gearbox is
not fitted properly, then the paddle will not
secure in place).
• Align the assembled puree accessory with the
motor body part and click the two parts together.
Plug in.
• Dip the puree accessory into the ingredients and
switch on the appliance.
• Using a gentle up and down motion, move the
puree accessory through the ingredients until the
desired texture is achieved.
• Release the Smart Speed switch and ensure the
puree accessory has completely stopped turning
before removing it from the food.
• After use, unplug the appliance. Remove the
paddle (9c) by turning clockwise.
• Press the release buttons to detach the puree
accessory from the motor part. Separate the
gearbox from the shaft by turning counter-
clockwise.
Caution
• Never use the puree accessory in a saucepan
over direct heat.
• Always remove the saucepan from the heat and
allow to cool slightly.
• Sit the saucepan or bowl on a stable, flat surface,
and support it with your free hand.
• Do not tap the puree accessory on the side of the
cooking vessel during or after use. Use a spatula
to scrape excess food away.
• For best results when mashing never fill a
saucepan or bowl more than half full with food.
• Do not process more than one batch without
interruption.
• Let the appliance cool down for 4 minutes before
you continue processing.
Recipe Example: Mashed Potatoes
1 kg cooked potatoes
200 ml warm milk
• Place the potatoes in a bowl and mash for 30
seconds (3/4 way on the Smart Speed switch)
• Add the milk. Resume mashing for another 30
seconds.
Chopper Accessory (D)
The choppers (10/11) are perfectly suited for
chopping meat, hard cheese, onions, herbs, garlic,
vegetables, bread, crackers and nuts.
12
Refer to the Processing Guide D for maximum
quantities, recommended times and speeds.
Maximum operation time for the «hc» chopper:
2 minutes for large amounts of wet ingredients,
30 seconds for dry or hard ingredients or amounts
< 100g. Immediately stop processing when motor
speed decreases and/or strong vibrations occur.
Before Use
• Pre-cut foods into small pieces for easier
chopping.
• Remove any bones, tendons and gristle from
meat to help prevent damage to the blades.
• Make sure the anti-slip rubber ring (10d/11d) is
attached to the bottom of the chopper bowl.
Assembly and Operation
• Carefully remove the plastic cover from the
blade.
• The blades (10b/11b) are very sharp! Always hold
them by the upper plastic part and handle them
carefully.
• Place the blade on the center pin of the chopper
bowl (10c/11c). Press it down and give it a turn so
that it locks into place.
• Fill the chopper with food and put on the lid
(10a/11a).
• Align the chopper with the motor part (4) and
click together.
• To operate the chopper, switch on the appliance.
During processing, hold the motor part with one
hand and the chopper bowl with the other.
• Always chop harder foods (e.g. parmesan
cheese) at full speed.
• When chopping is complete, unplug and press
the release buttons (5) to detach the motor part.
• Lift the lid up. Carefully take out the blade before
pouring out the contents of the bowl. To remove
the blade, slightly turn it then pull it off.
Caution
• Do not use the chopper accessories (10/11) with
chopping blades to process extremely hard
foods, such as unshelled nuts, ice cubes, coffee
beans, grains, or hard spices e.g. nutmeg.
Processing these foods could damage the
blades.
• Never place the chopper bowls in the microwave
oven.
«hc» Recipe example: Honey-Prunes (as a pancake
stuffing or spread):
50 g prunes
70 g creamy honey
10 ml water (vanilla-flavoured)
• Fill the «hc» chopper bowl with prunes and
creamy honey.
• Chop 4 seconds at maximum speed (fully press
the Smart Speed switch)