Getting Started - Jennair JFFCC72EFS Manual De Uso

INSTALLATION CHECKLIST
✔ Electrical Power
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Plug refrigerator into a grounded 3 prong outlet.
■
✔ Doors
If doors need to be removed during installation, see the
■
"Remove and Replace Doors" in the instructions.
Check that handles are secure and installed according to the
■
instructions.
Doors seal completely.
■
Refrigerator is level. (Remove base grille and adjust leveling
■
feet so they are snug against the floor.)
Doors are even across the top. (Use door alignment feature if
■
necessary.)
Base grille is properly attached to the refrigerator.
■
✔ Ice and Water System (on some models)
Connect refrigerator to a cold water supply with 20-120 psi
■
water pressure, as specified in the instructions.
Make sure the household water supply is connected and
■
turned on.
Check that the water supply line behind refrigerator is not
■
kinked.
Only use recommended water supply tubing, copper, or PEX,
■
as specified in the instructions.
Install water filter according to the instructions.
■
Flush water system with 3 gallons (11.4 L) of water, as
■
specified in the instructions.
Check for water leaks at all connections.
■
Turn on ice maker if refrigerator is connected to water supply.
■
(If not connected to water supply, turn off ice maker.)
✔ Final Checks
Install air filter according to instructions in corresponding
■
packaging.
Remove all shipping material.
■
Set temperature controls to the recommended setting.
■
Save instructions and other literature.
■
Send in Registration Card or register your product online.
■
WATER FILTER INSTALLATION
Locate the water filter compartment in the lower left-hand side
■
of the refrigerator compartment. Push on the right side of the
filter door to open.
Align the arrow on the water filter cap with the cutout notch in
■
the filter housing and insert filter.
6

GETTING STARTED

Once the filter is inserted, turn the filter clockwise 90° (1/4 turn)
■
until it locks into the housing.
Push water filter door closed to latch.
■
Flush 3 gallons (11.4 L) of water through the water system to
■
clear air from the water line and to keep the dispenser from
dripping and/or avoiding decreased dispenser flow.
NOTE: If the filter is not installed correctly, water may
dispense at a lower flow rate and there will be slower ice
production. Improper filter installation may also cause the
water filter housing to leak.
DOOR ALIGNMENT
Tools Required
Depending on the width of the door opening, the following tools
may be required to remove, replace, and align the refrigerator
doors.
Tools Needed:
1/4" hex nut driver – base grille, freezer drawer screws, and
■
brake/leveling feet
Tools Provided:
1/8" hex key – handle setscrews and door alignment
■
Door alignment tool instructions
Features:
Creates an even horizontal gap
■
between the refrigerator doors.
Solves door alignment issues
■
during installation and improves door seal.
Align Refrigerator Doors
✔ If doors are uneven:
Ensure the refrigerator is level.
■
Keeping both refrigerator doors closed, pull out the freezer
■
drawer. Locate the bottom hinge pin of the right-hand
refrigerator door. The alignment screw is inside the bottom
hinge pin.
Insert the short end of the 1/8" hex-key wrench (packed with
■
the Door Handle Installation Instructions) into the bottom hinge
pin until it is fully engaged in the alignment screw.
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.