Robern CRAFT Serie Instrucciones Importantes De Seguridad página 20

INSTALLATION DE VANITÉ HELDEN
Les instructions d'installation suivantes s'appliquent
spécifiquement au meuble-lavabo Helden. Ils s'appliquent aux
2. Wooden support
versions de 36" et 60" de large du meuble-lavabo.
(2 pcs)
LES PIÈCES
3. Stainless steel screw Ø6x40
(9 pcs)
(2) Support en acier /
Soporte de acero
4. Stainless steel screw Ø4x25
(9 pcs)
PRÉPAREZ LA VANITÉ
AVANT DE COMMENCER : Retirez tous les tiroirs et mettez-les
de côté dans un endroit sûr (voir les instructions à la page 6).
1. Mesurez et marquez les emplacements des raccords de
plomberie à l'arrière du meuble-lavabo.
2. PERÇAGE DE L'INTÉRIEUR DU MEUBLE VERS
Steel screw
5.
L'ARRIÈRE, utilisez une scie cloche pour découper les
emplacements marqués.
(6 pcs)
1
4x38mm
Ø
Jonathan Sowterathan Charles
- Fine Furniture
© 2021 Robern, Inc. 701 N. Wilson Ave. Bristol, PA 19007 U.S.A.
800.877.2376 www.robern.com
(1) Taquet mural /
Taco de pared
@ Copyright 2004 all right reserved by
4x38mm
Ø
Jonathan Sowterathan Charles
3. Stainless steel screw Ø6x40
ASSEMBLY INSTRUCTIONS
(9 pcs)
INSTALACIÓN DE HELDEN VANITY
Las siguientes instrucciones de instalación se aplican
2. Wooden support
1. Preset the cabinet on your desired
específicamente al tocador Helden. Son aplicables tanto para
(1 pcs)
location,and mark the location with a light
las versiones de 36" y 60" de ancho del tocador.
4. Stainless steel screw Ø4x25
pencil mark. Use tape or pencil to
(9 pcs)
transcribe the location of the back of the
PARTES
3. Stainless steel screw Ø6x40
cabinet pre-installed bracket to the wall.
(6 pcs)
Below this making is where you will install
[216-1239] Sac de matériel de montage /
the included metal wall- mount bracket. See
FIGURE 2.
Steel screw
5.
4. Stainless steel screw Ø4x25
2. Hold the bracket against the wall and mark
(6 pcs)
(6 pcs)
with pencil the locations of the bracket srew
[203-1564]
holes,ensuring levelness. See FIGURE 2.
(6) 1/4" x 1-9/16"
Vis / Tornillo
3. Drill a hole on each mark and then tap
anchor into hole until flush with surface.See
Steel screw 4x38mm
5. Ø
@ Copyright 2004 all right reserved by
Les quantités indiquées sont pour un meuble-lavabo de 36" po de largeur.
(3 pcs)
"ASSEMBLY INSTRUCTIONS BY WALL
Le meuble-lavabo de 60" de large est livré avec moins de composants.
Las cantidades que se muestran son para tocador de 36" de ancho.
TYPE" for mounting instructions base on
El tocador de 60"de ancho se envía con menos componentes.
your wall type: concrete,drywall, or drywall
and studs.
PREPARA LA VANIDAD
Jonathan Sowterathan Charles
4. Tighten the screws into the anchors while
ANTES DE COMENZAR: Retire los cajones y déjelos a un
maintaining constant pressure on the
lado en un lugar seguro (consulte la página 6 para obtener
anchor to set.Remove screw. Hold metal
instrucciones).
bracket over the inserted anchors, and
1. Mida y marque las ubicaciones de los extremos de las
tuberías en la parte posterior del tocador.
reinstall screws through the wall bracket
2. PERFORANDO DESDE EL INTERIOR DEL TOCADOR
holes, and lighten until snug against wall.
HACIA LA PARTE POSTERIOR, use una sierra de corona
See FIGURE 1.
para cortar los lugares marcados.
5. Install the cabinet on the wall bracket as
2
illsustrated in FIGURE 3.
- Fine Furniture
8
cabinet pre-installed
Below this making is
the included metal wa
FIGURE 2.
2. Hold the bracket again
with pencil the locatio
holes,ensuring leveln
3. Drill a hole on each ma
anchor into hole until
Bolsa de hardware de montaje
"ASSEMBLY INSTRU
TYPE" for mounting i
4x38mm
Ø
your wall type: concre
[203-1565] and studs.
(6) #8 x 1"
Vis / Tornillo
4. Tighten the screws into
maintaining constant
Jonathan Sowterathan Charles
- Fine Furniture
anchor to set.Remov
bracket over the inse
reinstall screws throu
- Fine Furniture
holes, and lighten unt
See FIGURE 1.
5. Install the cabinet on th
illsustrated in FIGURE
No. de pièce / Pieza n.° 209-1416 07/21/2021
Vanité de la Série Artisinale / Tocador de la Serie Craft
pencil mark. Use tape or pen
transcribe the location of the
cabinet pre-installed bracket
Below this making is where
the included metal wall- mou
FIGURE 2.
2. Hold the bracket against the w
with pencil the locations of t
holes,ensuring levelness. Se
3. Drill a hole on each mark and
anchor into hole until flush w
"ASSEMBLY INSTRUCTION
TYPE" for mounting instruct
your wall type: concrete,dryw
and studs.
4. Tighten the screws into the an
maintaining constant pressu
anchor to set.Remove screw
bracket over the inserted an
reinstall screws through the
holes, and lighten until snug
[203-1566]
(3) #8 x 1-1/2"
See FIGURE 1.
Vis / Tornillo
5. Install the cabinet on the wall
illsustrated in FIGURE 3.
4. T
5. In