Operation; Fonctionnement - ZENOAH KOMATSU BC2001 Manual De Instrucciones

Ocultar thumbs

Contenido

Tabla de contenido

OP1

OP2

OP3

(A)

(B)

(C)

OP4

English

8. Operation

@ @ @ @ @ @ @ @ e ?

@ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e

@ @ @ @ @ @ @ @ e ?

@ @ h ?

@ @

@ @ @ @

@ @

@ @ @ @

This product is specially

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

designed for nylon head

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

usage.

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ g

@ @ @ @ @ @ @ @

? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @

@ @ @ @ @ @ @ @

■ BALANCE UNIT

1. Put on strap and attach unit to strap.

2. Slide clamp up or down until unit

balances with head just touching the

ground. (OP1)

• You could (aprox. 10 – 30cm) apart the

unit from the ground when using saw

blade so that you feel easy of the

machine.

■ STARTING ENGINE

WARNING

The cutting head will start rotating

upon the engine starts.

1. Rest the unit on a flat, firm place. Keep

the cutting head off the ground and

clear of surrounding objects as it will

start rotating upon starting of the

engine.

2. Push the primer pump several times

until overflown fuel flows out in the clear

tube. (OP2)

3. Move the choke lever to the closed

position. (OP2)

(1) choke lever

(2) close

(3) open

(4) primer pump

4. While pulling the throttle lever

(OP3,1,2), set the ignition switch to the

"I (START)" position and release the

throttle. Then the throttle lever is in to

the "start position". (OP3)

(A) stop

(B) start

5. While holding the unit firmly, pull out the

starter rope quickly until engine fires.

(OP4)

IMPORTANT

• Avoid pulling the rope to its end or

returning it by releasing the knob. Such

actions can cause starter failures.

6. Move the choke lever downward to

open the choke. And restart the engine.

Français

8. Fonctionnement

@ @ @ @ @ @ @ @ e ?

@ @ @ @ @ @ @ @

@ @ @ @ @ @ @ @ e ?

@ @

@ @ h ?

@ @

@ @ h ?

@ @ @ @

@ @ h ?

@ @

@ @ h ?

@ @

@ @ h ?

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

Ce produit a été conçu pour

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

être exclusivement utilisé avec

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

une tête en nylon.

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

? @ @

@ @ g

? @ @

@ @ g

? @ @

@ @ g

? @ @

@ @ g

? @ @

@ @ g

? @ @

@ @ g

? @ @ @ @ @ @ @ @

@ @ @ @ @ @ @ @

? @ @ @ @ @ @ @ @

@ @ @ @ @ @ @ @

■ EQUILIBRAGE DE LA MACHINE

1. Mettre le harnais sur l'épaule et y

accrocher la débroussailleuse.

2. Faire glisser le collier vers le haut ou

vers le haut jusqu'à ce que la tête de

l'appareil soit droite au niveau du sol

(OP1).

• On peut relever la machine du sol pour

une utilisation plus facile (d'environ 10 à

30 cm) lorsqu'on utilise la lame de

tonte.

■ MISE EN MARCHE DU MOTEUR

AVERTISSEMENT

Faire attention que la lame de coupe se

mette à tourner dès que le moteur

démarre.

1. Poser la machine dans un endroit plat

et ferme. Ne pas poser la tête de coupe

sur le sol et dégager tout objet pouvant

être projeté par la lame qui se met à

tourner dès que le moteur démarre.

2. Appuyer plusieurs fois sur la pompe

d'amorçage jusqu'à ce que de

l'essence s'écoule par le tuyau de trop-

plein (OP2).

3. Placer le starter en position fermée

(OP2).

(1) levier du starter

(2) fermé

(3) ouvert

(4) Pompe d'amorçage

4. Tout en ramenant la manette de

commande des gaz vers vous,

commutez l'interrupteur d'allumage en

position "I (START)", puis relâchez la

manette.Puis positionnez la manette

des gaz en "position de démarrage".

(OP3)

(A) Arrêt

(B) Marche

5. Tout en maintenant fermement la

machine, tirer la poignée de démarrage

(OP4).

IMPORTANT

• Eviter de tirer à fond sur la corde de

démarrage ou de relâcher brutalement

@ @ @ @ @ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

@ @

@ @ @ @

? @ @

? @ @ @ @ @ @ @ @

Tabla de Contenido

Tabla de contenido

Este manual también es adecuado para:

Tr2000

Operation; Fonctionnement - ZENOAH KOMATSU BC2001 Manual De Instrucciones

8. Operation

8. Fonctionnement

Manuales relacionados para ZENOAH KOMATSU BC2001

Contenido relacionado para ZENOAH KOMATSU BC2001

Este manual también es adecuado para:

Tabla de contenido