Emptying The Collection Tank - TMB QUICK P12 Manual De Uso Y Mantenimiento

ENGINE HEAD DESCRIPTION
1. ON / OFF switch
2. handle
3.
4. Cable support hook
5. Technical data label
6. Power cable
7.
APPLIANCE SAFETY
The stages for making the appliance safe, thereby making it possible to carry out operations safely,
are as follows:
1.
2. Make sure that the plug (2) on the power cable (3) has been taken out of the mains supply socket
(4), and if not, disconnect it (Fig.2).
3. Wind the power cable under the appliance's lifting handle.
CAUTION: We recommend handling the power cable with dry hands to avoid serious injury.
CAUTION: To prevent damaging the power cable, disconnect the plug from the mains socket by
directly pulling the plug and not the cable.
1
3
2
1 2
VACUUMING DRY OBJECTS
To vacuum dry objects, do as follows:
1. Open the hooks on the tank, lift the head from the handle, place it gently on the ground.
2. Remove the FLOAT GROUP (A1) inside the tank.
3. Insert the vacuum hose (1) from the vacuum nozzle (2) on the collection tank, before pulling the
vacuum hose press the button (3) for unlocking the catch (Fig.1).
4. Select the most suitable accessory for the work to be carried out. Insert the selected accessory into
the vacuum hose, if necessary also use the extension tubes.
5. Insert the plug of the power supply cable in the mains supply socket.
ATTENTION:
connection point (see Technical Data). Please contact your electrical energy supplier if in
doubts concerning mains impedance on the connecting point.
CAUTION: Do not insert the power cable into the socket of the mains plug with wet hands.
6.
7. Start work.
2
1
1
3
4
WORK
(A1)
FILTER CLEANING
four times. (1). Now machine is ready to operate.
palm of the hand and press the push-button three or four times (2). Now machine is
ready to operate.
VACUUMING WET OBJECTS
To aspirate wet objects, perform the following:
1. Open the hooks on the tank, lift the head from the handle, place it gently on the ground.
2. Check the presence of the FLOATING GROUP (A1) inside the tank.
3. Insert the vacuum hose (1) from the vacuum nozzle (2) on the collection tank, before pulling the
vacuum hose press the button (3) for unlocking the catch (Fig.1).
4. Select the most suitable accessory for the work to be carried out. Insert the selected accessory into
the vacuum hose, if necessary also use the extension tubes.
5. Insert the plug of the power supply cable in the mains supply socket.
ATTENTION:
connection point (see Technical Data). Please contact your electrical energy supplier if in
doubts concerning mains impedance on the connecting point.
CAUTION: Do not insert the power cable into the socket of the mains plug with wet hands.
6.
7. Start work.
2
1
1
3

EMPTYING THE COLLECTION TANK

At the end of the work, and before carrying out any type of maintenance, perform the following
operations:
1. Take the appliance to where its collection tank is emptied.
N.B: the place designated for this operation must comply with current environmental protection
regulations.
CAUTION: These operations must be carried out using gloves to protect the hands.
2.
3. Remove the plug (2) on the power cable (3) from the mains power supply socket (4) (Fig.2).
WARNING: To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
4. Remove the vacuum head (5) using the handle on top of it, before removing the head loosen the
locking catches (6) on the side of the collection tank (7) (Fig.3) and lay it on the ground.
CAUTION: When overturning the collection tank, hold the appliance using the handlebars (11).
5. Empty the collection tank.
20
(A1)
Fig.1).