Description Of Symbols - Silverline DIY 350W Manual Del Usuario

GB
Introduction
Thank you for purchasing this Silverline tool. This manual contains information necessary for safe
and effective operation of this product. This product has unique features and, even if you are familiar
with similar products, it is necessary to read this manual carefully to ensure you fully understand the
instructions. Ensure all users of the tool read and fully understand this manual.

Description of Symbols

The rating plate on your tool may show symbols. These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
CAUTION!
For indoors use only!
Always disconnect from the power supply when adjusting, changing accessories,
cleaning, carrying out maintenance and when not in use!
Class I construction (protective earth)
Environmental Protection Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with your local authority
or retailer for recycling advice.
Conforms to relevant legislation and safety standards.
6
Original Instructions
Technical Abbreviations Key
V Volts
~, a.c Alternating current
A, mA Ampere, milli-Amp
n
No load speed
0
n Rated speed
° Degrees
Ø Diameter
Hz
Hertz
, DC Direct current
W, kW Watt, kilowatt
/min or min Operations per minute
-1
rpm
Revolutions per minute
dB(A) Decibel sound level (A weighted)
m/s Metres per second squared (vibration magnitude)
2
Specification
Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V~, 50Hz
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350W
Motor type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Induction
Operating time (max). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30min (S2 duty cycle)
Motor speed:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No load speed. . . . . . . . . . . . . . . . . . . . . . .
Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Chuck size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm (1.5 - 13mm)
Table size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 x 160mm
Table Tilt Angle Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +/- 45°
Chuck centre to column (throat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104mm
Chuck/Spindle Travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mm
Chuck to base (max). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .295mm
Chuck to table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-210mm
Protection class: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ingress protection: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP20
Dimensions (L x W x H):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 x 225 x 440mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5kg
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Sound and vibration information:
Sound Pressure L : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66dB(A)
PA
Sound Power L : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79dB(A)
WA
Uncertainty K: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3dB
The sound intensity level for the operator may exceed 85dB(A)
and sound protection measures are necessary.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and limit the time
of exposure if necessary. If sound levels are uncomfortable, even with ear protection, stop using the
tool immediately and check the ear protection is correctly fitted and provides the correct level of
sound attenuation for the level of sound produced by your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness, tingling
and reduced ability to grip. Long-term exposure can lead to a chronic condition. If necessary, limit
the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool with
hands below a normal comfortable temperature, as vibration will have a greater effect. Use the
figures provided in the specification relating to vibration to calculate the duration and frequency
of operating the tool.
n
: 1440/min
0
n
: 580, 850, 1220, 1650 & 2650/min
0