Peg-Perego OD0021 Manual Del Usuario página 10

SYMPTOM:
Short runtime.
POSSIBLE CAUSE: SOLUTION:
• Vehicle has too much load. • Reduce the load on the vehicle.Too much weight,
steep slopes, thick grass, sand, etc. or any
combination of these conditions can overload
the vehicle causing reduced runtime.
• Battery is low. • See solution for "Battery low or dead" above.
• Battery is low or near end • See solution for "Battery dead" above.
of life.
SYMPTOM:
One wheel turns but not the other.
POSSIBLE CAUSE: SOLUTION:
• Vehicle is in low or rewerse. • This is normal when in low speed or reverse
because the wheels act like an automotive
differential. This makes turning easier. If one
wheel is stalled or stopped the other wheel gets
all the power. Shift to high speed to get full
power to both wheels.
• Motor wire is disconnected. • See solution for "Motor wire disconnected"
above.
• Bad high/low switch. • Replace high/low switch. Order part # MEPU0002.
SYMPTOM:
High Speed - One wheel only
Low Speed - NO
Reverse Speed - NO
SOLUTION:
POSSIBLE CAUSE:
• One motor wire is • See solution for "Motor wire disconnected"
disconnected. above.
SYMPTOM:
High Speed - OK (both wheels)
Low Speed - NO
Reverse Speed - NO
SOLUTION:
POSSIBLE CAUSE:
• Bad high/low switch. • Replace high/low switch. Order part # MEPU0002.
SYMPTOM:
High Speed - NO (neither wheels)
Low Speed - OK
Reverse Speed - OK
POSSIBLE CAUSE: SOLUTION:
• Remove the high speed "lock-out" . See fig. # 58 &
• High Speed is in the "lock-
out" position. 59).
SYMPTOM:
High Speed - One wheel only
Low Speed - OK
Reverse Speed - OK
POSSIBLE CAUSE: SOLUTION:
• Replace high/low switch. Order part # MEPU0002.
• Bad high/low switch.
SYMPTOM:
High Speed - OK
Low Speed - OK
Reverse Speed - NO
POSSIBLE CAUSE: SOLUTION:
• Bad forward/reverse • Replace forward/reverse switch. Order part #
MEPU0003.
switch.
SYMPTOM:
High Speed - NO
Low Speed - NO
Reverse Speed - OK
POSSIBLE CAUSE: SOLUTION:
• Bad forward/reverse • Replace forward/reverse switch. Order part #
MEPU0003.
switch.
SYMPTOM:
Vehicle stops intermittently, then restarts after several seconds.
POSSIBLE CAUSE: SOLUTION:
• Automatic Circuit Breaker • Reduce the load on the vehicle.Too much weight,
has tripped because of steep slopes, thick grass, sand, etc. or any
overloading. combination of these conditions can overload
the vehicle.
• Accelerator switch not • See solution for "Accelerator switch not operating
properly" above.
operating properly.
All manuals and user guides at all-guides.com
SYMPTOM:
Circuit breaker trips when the battery is plugged into the black vehicle
harness.
POSSIBLE CAUSE:
• Accelerator switch not
SYMPTOM:
Loud clicking noise heard when toy is being used.
POSSIBLE CAUSE:
• Gear are stripping.
SYMPTOM:
Battery makes a bubbling or sizzling noise when charging.
POSSIBLE CAUSE:
• Battery is being charged.
SYMPTOM:
Wheels spin too much.
POSSIBLE CAUSE:
• Not enough weight on rear
• Motor wire is disconnected.
SYMPTOM:
Brake not working.
POSSIBLE CAUSE:
• Accelerator switch not
• Bad accelerator switch.
SYMPTOM:
Power Lift bed stops working sometimes.
POSSIBLE CAUSE:
• Automatic motor overload
SYMPTOM:
Power Lift bed makes a clicking sound when the buttons are depressed.
POSSIBLE CAUSE:
• Safety slipping mechanism
SYMPTOM:
Power Lift bed does not work at all.
POSSIBLE CAUSE:
• The wiring is not properly
A1
SOLUTION:
• Check accelerator switch wire locations. Remove
connectly properly. footboard by prying with a screwdriver at its
base. (See fig. # A1 & A2 for footboard removal
and proper wire locations).
SOLUTION:
• Replace
ASGI9950XW.
SOLUTION:
• It is normal for some batteries to make some
noise during charging. No action is needed.
SOLUTION:
• Add some weight to the dump bed.
wheels.
• See solution for "Motor wire disconnected" .
SOLUTION:
• Check accelerator switch wire locations. Remove
connectly properly. footboard by prying with a screwdriver at its
base. (See fig. # A1 & A2 for footboard removal
and proper wire locations).
• Replace acceleratior switch. Order part #
ASGI0082Y.
SOLUTION:
• Wait 15 - 30 seconds for the overload protection
protection device is device to reset. Note: when the outside
working. temperature is high, the automatic motor
overload protection device may operate more
often to protect the motor. Reduce the amount of
weight in the bed.
SOLUTION:
• This slipping is normal at the top and bottom of
is working. the lift range. No repair is needed.
SOLUTION:
• Check the battery o main wiring connection. See
connected. diagram # 28.
• Check the wiring connectors on underside of
Gator. See diagram # 24.
motor/gearbox assembly part
A2
#