Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
WI-FI SETUP
For detailed instructions for connecting the thermostat to a Wi-Fi network and registering it to an Aprilaire account,
refer to the Wi-Fi Quick Start Guide included in the box .
INSTALLATION
THERMOSTAT INSTALLATION LOCATION RECOMMENDATIONS
Thermostat should be mounted:
Do not mount thermostat:
• On an interior wall, in a frequently
• Behind doors, in corners or other dead air spaces .
occupied space .
• In direct sunlight, near lighting fixtures, or other appliances that
• Approximately 5' above floor .
give off heat .
• At least 18" from outside wall .
• On an outside or unconditioned area wall .
• Thermostat can be mounted to a
• In the flow of a supply register, in stairwells, or near outside doors .
vertical junction box .
• On a wall with concealed pipes or ductwork .
THERMOSTAT MOUNTING
1 . Remove the rear mounting plate from the thermostat .
2 . Pull wires through the opening on the rear mounting plate .
3 . Position and level the mounting plate of the thermostat on wall and
mark the hole locations with a pencil .
4 . Drill 1/4" holes and insert supplied anchors (drywall only) .
5 . Place mounting plate over anchors, insert and tighten screws .
6 . Seal wire entry holes to prevent drafts affecting temperature readings .
EQUIPMENT CONTROL MODULE INSTALLATION LOCATION RECOMMENDATIONS
Note: Installer must touch a grounded metal object before handling the Equipment Control Module to avoid potential
damage due to electrical discharge .
Equipment control module should be mounted:
• In a location where the temperature will not exceed
158°F (70°C) or drop below 32°F (0°C) .
EQUIPMENT CONTROL MODULE MOUNTING
The Equipment Control Module has the following features to simplify mounting and wiring and provide for a clean
and neat installation .
• Six (6) mounting holes . One on each corner and two centered top and bottom . Any combination of these holes may
be utilized . Mount the Equipment Control Module using 2 to 4 #8 screws appropriate for the mounting surface
substrate . (See Figure 2 .)
• Wires can be routed through
the top, bottom, sides or back .
• Nylon wire ties can be used
to secure wires in 10 places .
Installation Steps
1 . Select mounting location .
2 . Pull from bottom to remove
front cover . (See Figure 1 .)
3 . Mount base using 2 to 4 #8
screws (field supplied) .
Figure 1
2 English
Do not mount equipment control module:
• On foundation walls or on the HVAC equipment or
ductwork . These locations can cause moisture to
condense on the equipment control module .
Figure 2
INSTALLATION
THERMOSTAT WIRING
Wire specifications:
18-24 gauge thermostat wire
Installation notes:
• Ensure power at the HVAC equipment is off .
• Loosen screw terminals, insert stripped wire
and re-tighten .
• Push the excess wire back into the opening and plug the wall opening to prevent drafts .
1 – Connection to terminal 1 at equipment control module
2 – Connection to terminal 2 at equipment control module
3 – Connection to terminal 3 at equipment control module
T1 & T2 – Remote temperature sensor (optional)
REMOTE TEMPERATURE SENSOR (OPTIONAL)
A remote temperature sensor can be used for control if the thermostat is to be mounted in a concealed location
or a remote sensor can be averaged with the thermostat sensor to control a large space . An 8051 flush mount
or 8053 surface mount remote temperature sensor can be attached to the T1 and T2 terminals and mounted in a
recommended area . The remote sensor must be enabled in the installer set-up menu, and once enabled will override
or be averaged with the thermostat's internal temperature sensor, based on the setting .
Remote temperature sensor should be
mounted:
• On an interior wall, in a frequently occupied
space .
• Approximately 5' above floor .
• At least 18" from outside wall .
• Using less than 300' of wire .
Do not mount remote sensor:
• Behind doors, in corners or other dead air
spaces .
• In direct sunlight, near lighting fixtures, or
other appliances that give off heat .
• On an outside or unconditioned area wall .
• In the flow of a supply register, in stairwells,
or near outside doors .
• On a wall with concealed pipes or ductwork .
• Near 120 VAC lines .
1
2
3
T1 T2
1
2
3
T1 T2
English 3
Publicidad
Capítulos
Tabla de contenido
Solución de problemas
