Setting Mode; Recording Mode - DEXAPLAN DV 622 Manual Del Usuario

Setting mode

PAL
EXIT
Time Setup
!
Press the "Menu" button [5] to access the setting mode. A screen with
5 icons is displayed (see Figure G): The top four icons symbolise the
settings, and the bottom icon
mode.
The blue frame shows the function to be changed. You can move this with
the buttons [4] and [2].
The framed setting can be selected by pressing the "OK" button [13].
You can leave the setting mode by pressing the "Menu" button [5].
If no button is pressed for 3 minutes in the setting mode, the setting mode
is ended automatically.
- Setting the date and time
The event recorder has an on-screen clock. The date and time from this are
saved together with the stored images.
!
Select the icon.
!
Press the "OK" button [13] to confirm the selection. The date
(YYYY/MM/DD) is displayed at the bottom in the image. You can
change the position which is red: Move the red position by pressing
the buttons [4] and
repeated pressing of the button
the red position by pressing the buttons
!
When you have made all your desired changes, confirm your changes
by pressing the "OK" button [13].
Note:
The date and time settings are retained for up to 12 hours if the power
supply is switched off.
/ - Switching recording mode ON/OFF
!
Select the icon.
!
You can switch the recording mode ON
is displayed at the bottom of the screen) or OFF
Detection OFF" is displayed at the bottom of the screen) by repeated
pressing of the "OK" button [13].
If recording mode is activated, the display
mode.
If recording mode is switched off, the display
live image mode.
Tips:
You can also select the corresponding setting in the live image mode
directly by repeated pressing of the button [3].
The recording mode cannot be switched off in the live image mode if
recording is in progress.
All manuals and user guides at all-guides.com
Fig. G
is used to exit from the setting
EXIT
[2]. You reach the time (HH:MM:SS) by
[4]. You can change the value of
[3] and [12].
("Motion Detection ON"
("Motion
[9] lights in the live image
[9] does not light in the
Selection of the recording mode (still image
mode )
Still images or video sequences can be recorded automatically when
movement is detected.
!
Select the icon.
!
Select the still image mode
at the bottom of the screen) or the video mode
AVI" is displayed at the bottom of the screen) by repeated pressing of
the "OK" button [13].
If the still image mode is selected in the live image mode, the symbol
is displayed on the screen and the LED
If the video mode is selected in the live image mode, the symbol
displayed on the screen and the LED
Tip:
You can also select the corresponding setting in the live image mode
directly by repeated pressing of the button [12] (Photo / AVI).
The still image / video mode setting cannot be changed in the live image
mode if recording is in progress.
PAL
NTSC
/ - Selection of the TV system
!
For use in Europe, you must set the system to PAL (50 Hz image
refresh frequency) (factory setting).
If you have not adjusted the system to the correct TV system, the displayed
picture will be striped or black and white.
!
Select the icon .
PAL
!
You can select the PAL or NTSC
PAL
of the "OK" button [13].
EXIT
- Leaving the setting mode
!
Select the icon.
EXIT
!
Press the "OK" button [13] to confirm the selection.
You can also leave the setting mode by pressing the "Menu" button [5].

Recording mode

You cannot activate this mode if the device is in playback mode. Only the
full screen image displayed on the screen in the live image mode can be
stored. The picture-in-picture format can be displayed but not recorded.
The device can only store images from one video input.
!
Switch on the recording mode. Press the "Motion Detection" [3]
button for this; the LED
mode, the symbol at the top left of the screen flashes for approx.
75 seconds. During this time, the image is "learnt" by the internal
software (= learning phase). The software adapts itself to constant
image changes in order to not repeatedly by record the same
movements. The image learning is performed every time the recording
mode is activated.
Avoid movements in the camera image during the learning phase
otherwise the sensitivity of the motion detection will be reduced.
/ video
("Capture Format Photo" is displayed
("Capture Format
[8] does not light.
[8] lights.
setting by repeated pressing
NTSC
[9] lights. After activating the recording
GB / IE - 25
is