Specified Conditions Of Use; Ec Declaration Of Conformity; Mains Connection - Milwaukee MS 216 SB Manual Del Usuario

The handle lock must always be engaged when transporting the
mitre saw.
Only use the saw with guards in good working order and properly
maintained, and in position.
Keep the floor area free of loose material e.g. chips and cut-offs.
Only use saw blades which have been properly sharpened. It is essen-
tial to adhere to the maximum speed specified on the saw blade.
Do not use any flanges other than those supplied or indicated in the
instruction manual to secure the saw blade.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Ensure that the machine is always stable and secure (e.g. fixed to a
bench)
Long workpieces must be adequately supported.
Do not use cracked or distorted saw blades.
Transport and store the tools in a suitable receptacle.
Before using the tool please read the instructions. If possible have the
tool demonstrated.
GB
GB
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
Do not point laser at reflective surfaces, Avoid exposure to laser
radiation. Laser may emit hazardous radiation.
Do not replace the installed laser with a different type.

SPECIFIED CONDITIONS OF USE

The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium profiles, Non-
ferrous metals and plastics.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized documents.
EN 61029-1, EN 61029-2-9, EN 55014-1:2006 + A1:2009, EN 55014-
2:1997 + Corrigendum 1997 + A1:2001 + A2:2008, EN 61000-3-
2:2006 + A1:2009 + A2:2009, EN 61000-3-3:2008,
in accordance with the regulations 2006/42/EC, 2004/108/EC
Winnenden, 2012-04-12

MAINS CONNECTION

Connect only to single-phase AC current and only to the system
voltage indicated on the rating plate. It is also possible to connect
English
22
Rainer Kumpf
Director Product Development
Authorized to compile the technical file
to sockets without an earthing contact as the design conforms to
safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at: Milwau-
kee Electric Tool, Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting
the machine.
Always disconnect the plug from the socket before
carrying out any work on the machine.
Wear ear protectors!
Always wear goggles when using the machine.
Always keep hands away from the path of the saw
blade.
Never expose tool to rain.
CAUTION! WARNING! DANGER!
Do not stare into beam.
This product corresponds to the laser class 1M in
accordance with IEC60825-1.
Do not dispose of electric tools together with
household waste material! In observance of European
Directive 2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with
national law, electric tools that have reached the end of
their life must be collected separately and returned to
an environmentally compatible recycling facility.
Class II construction, tool in which protection against
electric shock does not rely on basic insulation only, but
in which additional safety precautions, such as double
insulation or reinforced insulation, are provided.