Cequent Performance Products 51197 Instrucciones De Instalación

Vehicle
Frame
Spring shackle
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51197F
Wrenches: 21mm, 22mm, 3/4", 7/8"
Drill Bits: None
5
6 2
1
Qty. (4) Hex Bolt, M14 x 2.0 x 45mm CL10.9
1
Conical Toothed Washer, 5/8" (larger washer)
Qty. (4)
2
Carriage Bolt, 1/2"-13 x 1-3/4" Gr.5
Qty. (2)
3
1. In some cases it may help to lower spare tire from underneath of truck for ease of installation, but is usually not necessary.
2. If truck has existing hitch remove it including existing bolts in bottom end of truck frame rails and bottom of bumper. Return old hitch and
bolts to vehicle owner.
3. For trucks without an existing hitch remove 14mm bolt from bottom end of each truck frame rail and return to owner.
4. Raise new hitch into position locating slots in hitch over holes with existing weldnuts in bottom of truck bumper and bottom end of truck
frame rails.
5. Install supplied 14mm bolts and larger conical toothed washers through hitch and into existing weldnuts in end of truck frame and bumper as
shown above. On forward attachments install supplied carriage bolts and blocks through large access holes on inside or outside of truck
frame and down through holes in bottom of truck frame and through slots in hitch.
6. Attach smaller conical washers and nuts to forward bolts both sides.
7. Torque nuts from previous step and 14mm bolts installed in Step 5. to specifications below.
8. Raise spare tire if lowered back up into place.
Tighten 1/2"-13 Gr.5 bolts with torque wrench to 75 Lb.-Ft. (102 N*M) Tighten M14 x 2.0 CL10.9 bolts to 115 Lb.-Ft. (156 N*M).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010, 2012 Cequent Performance Products
Installation Instructions
GMC Sierra/Chevrolet Silverado 2500HD & 3500HD
Short-bed pickups only. Does not fit long-bed trucks.
includes 2500HD Extended & Crew-Cab - 2 & 4WD Short-bed only
3500HD Crew - 2 & 4 WD Shortbed only
GMC 2500HD / 3500HD Denali Crew-Cab with Short-bed only
Bumper
Fascia
4
3
5
6
Bumper attachment
14mm weldnuts,
typical both sides
2
1
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3
This hitch will not fit long-bed trucks,
Will fit all 2500HD/3500HD short-bed trucks
Frame attachment
14mm weldnuts,
typical both sides
1
1
2
Block,1-1/2" x 2" with square hole
Qty. (2)
4
0
Conical Toothed Washer, 1/2" (smaller washer)
Qty. (2)
5
Hex Nut 1/2"-13
Qty. (2)
6
Another Fine Cequent Performance Products hitch
Sheet 1 of 3 51197N
Part Numbers:
51197
97197
.
Max Gross
Trailer WT (LB)
11,000 (4994Kg) 1100 (499 Kg)
6000 (2724 Kg)
Note!
of the proper years.
2
2-1-12
Form: F205 Rev A 5-6-05
Max Tongue
WT (LB)
600 (272 Kg)
Rev. B