Product Features; Noise/Vibration Information - Bosch Professional GTM 12 JL Manual Original

OBJ_BUCH-1688-004.book Page 39 Tuesday, July 9, 2013 11:59 AM
The machine is designed with sufficient capacity for sawing
hard and softwood as well as press and particle board.
When operating as a table saw, the power tool is not permit-
ted for cutting aluminium or other non-ferrous metals or al-
loys.
The light of this power tool is intended to illuminate the power
tool's direct area of working operation and is not suitable for
household room illumination.

Product Features

The numbering of the components shown refers to the repre-
sentation of the power tool on the graphic pages.
1 OFF button
2 ON button
3 Mounting holes
4 Recessed handles
5 Allen key (size 6 mm)/slotted screwdriver
6 Metal bar of tilt protector
7 Saw blade
8 Dust bag
9 Sawdust ejector
10 Locking screw of lever 11
11 Bracket
12 Allen screw (size 6 mm) for mounting of saw blade
13 Spindle lock
14 Clamping flange
15 Interior clamping flange
16 Laser lens cover
Chop and Mitre Saw Features
17 Release button of the tool arm
18 Handle
19 Laser unit
20 Retracting blade guard
21 Material clamp
22 Saw table of the chop and mitre saw
23 Scale for mitre angle
24 Insert plate
25 Locking knob for various mitre angles
26 Mitre detent lever
27 Detents for standard mitre angles
28 Mounting holes for material clamp
29 Saw-Table extension
30 Fence
31 Stop screw for 33.9° bevel angle (vertical)
32 Stop bolt for 33.9° bevel angle (vertical)
33 Lighting unit
34 Light switch ("Light")
35 Switch for marking of cutting line ("Laser")
36 Bevel lock lever
37 Transport safety-lock
38 Allen screws (6 mm) of the fence
39 Laser warning label
Bosch Power Tools
40 Allen screws of the saw table extension
41 Threaded rod
42 Wing bolt
43 Locking bracket
44 Fine scale
45 Indicator for bevel angle
46 Scale for bevel angle
47 Screws for insert plate
48 Rubber cap (front)
49 Adjustment screw for laser position
(parallelism)
50 Adjustment screw for laser position
(flush levelling)
51 Rubber cap (side)
52 Adjustment screw for laser position
(lateral deviation)
53 Screw for fine scale
54 Screw for bevel angle indicator
55 Allen screw (size 3 mm) for standard bevel angle 0°
(vertical)
56 Allen screw (size 3 mm) for standard bevel angle 45°
(vertical)
Table Saw Features
57 Saw table of the table saw
58 Riving knife
59 Parallel guide
60 Push stick
61 Blade guard
62 Clamping handle of the parallel guide
63 Scale for clearance of the saw blade to the parallel guide
64 Lower saw blade cover
65 Pins for attachment of the hold-down stick
66 Clamping lever
67 Clearance indicator
68 Screw for parallel guide clearance indicator
69 Guide of the parallel guide
70 Adjustment screw for tightening tension of guide 69
71 Screws inside the glide pad of the parallel guide
72 Set screws of the parallel guide
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.

Noise/Vibration Information

Measured sound values determined according to EN 61029.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Operation as Chop and Mitre Saw:
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a =3,5 m/s , K=1,5 m/s .
h
English | 39
1 609 92A 0BP | (9.7.13)