Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
O=RingMaintenance
Purchasean O-Ring Repair Kit, item 75116, at your local Sears
or by calling 1-800-4-1VlY-NOME ( 469-4663) or online at
www.sears.com. It is not includedwith the pressurewasher.
This kit includesreplacemento-rings and a water inletfilter.
Referto the instruction sheet providedin the kit to serviceyour
unit's o-rings.
,& WARNING The high pressure stream of water that
this equipment produces could cut through skin
and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repairleakingconnections with sealant o f any kind.
Replace o-ring or seal.
PumpMaintenance
Changing Pump Oil
Changeoil after first 50 hours of operation and then every
200 hours or 3 months, whichever occurs first.
NOTICE When changing pump oil, use only high quality
nondetergent 30 weight oil. Use no special additives.
NOTICE Pump oil is available as an optional accessory, it is
not included with the pressure washer. Pump oil, item 75127
is available at your local Searsor by calling 1-SOO-4-1VlY-NOIVlE
(469-4663) or online at www.sears.com..
Change pumpoil as follows:
1.
Cleanarea around brass oil drain plug at bottom of
pump.
2.
Remove oil drain plug. Drain oil completely into an
approved container.
3.
When oil has completely drained, install oil drain plug
and tighten firmly.
4.
Cleanarea around pump oil dipstick. Remove dipstick
and fill pump with recommended oil to "Fuir' mark on
dipstick (typically 0.35L or 12 oz.).
5.
install pump oil dipstick.
6.
Wipe up any spilled oil.
ENGINEMAINTENANCE
,_. WARNING Unintentional sparking could cause fire or
"_llh
electric shock resulting in death or
serious injury.
WHEN ADJUSTING ORMAKING REPAIRS TOYOUR PRESSURE
WASHER
• Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTINGFOR ENGINESPARK
= Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF, SG,
SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
oF
104 _w
86
_,
68
o
eo
5O
32 __,-
14
-4
-22
oC
•
40
o__
30
__20
,__10
_m
_
0
-10
-20
-30
* Below 40°F (4°C) the use of SAE 30 will result in hard starting.
** Above 80°F (27°C) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking Oil Level
Oil level should be checked prior to each use or at least every
8 hours of operation. Keep oil level maintained.
1.
Make sure pressure washer is on a level surface.
2.
Cleanarea around oil fill, remove oil cap/dipstick and
wipe dipstick with clean cloth, insert dipstick, DO NOT
screw in. Removeand check oil level.
3.
Verify oil is at Full mark (A) on dipstick.
4.
Replaceand tighten oil cap/dipstick.
Adding Engine Oil
1.
Make sure pressure washer is on a level surface.
2.
Checkoil level as described in Checking Oil Level.
3.
if needed,slowly pour oil into oil fill opening to the Full
mark (A) on dipstick. DO NOT overfill.
4.
Replaceand tighten oil cap/dipstick.
19
Publicidad
Tabla de contenido
